Re-enable parselogs testing for fvp-base and corstone1000-fvp, and add
an ignore file for the relevant entries. Also, increase the testing
being done on corstone1000-fvp.
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add the bits to enable poky-altcfg to boot to prompt on fvp-base.
Unfortunately, ssh takes a very long time to come up, which causes the
ssh test to timeout. So, don't enable this by default in CI.
Also, switch to building full-cmdline instead of sato, since we're never
actually testing the graphics on this platform.
Signed-off-by: Jon Mason <jon.mason@arm.com>
The Secure Debug functionality can be enabled on MPS3 by using the new
corstone1000-mps3-secure-debug.yml kas file. The kas file adds the new
secure-debug machine feature. The TF-M recipe adds the needed TF-M
build flags and patches in order to make the Secure Debug work.
This way, the Corstone-1000 will only boot fully if a debugger is
connected and a debug authentication is initiated.
Signed-off-by: Bence Balogh <bence.balogh@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
The edk file removed xorg from being tested, which is currently working
on qemuarm and qemuarm64. Also, the section name collies with one in
fvp.yml, which has other things that are removed. Remove this removal
to get things working as expected.
Signed-off-by: Jon Mason <jon.mason@arm.com>
With the resolution of meta-clang issue 766 and
OE-Core 15d09b02b2632ab1cabc3b1bd9f521e6d3d3b83f
many of the settings are no longer necessary to be set as part of our
CI. Remove them, as it is causing other issues with CI.
Signed-off-by: Jon Mason <jon.mason@arm.com>
Update the Arm Binary toolchain to version 13.3-rel1. The upper to
lowercase 'r' in rel was intentional, as the exact match is needed for
devtool to properly determine the correct version.
Signed-off-by: Jon Mason <jon.mason@arm.com>
uefi-test is failing on qemuarm64-secureboot with TS enabled with a "Bus
Error". This regression is caused by the update of QEMU from v8.2.1 to
v9.0.0. Temporarily disable this test (via disabling ts-smm-gateway) to
get CI green until it can be root caused.
Signed-off-by: Jon Mason <jon.mason@arm.com>
We boot genericarm64 inside a qemu, so add the pregenerated keys to speed
up testing. This isn't a risk because we don't publish the images.
Signed-off-by: Ross Burton <ross.burton@arm.com>
The BB_HASHSERVE_UPSTREAM has issues which cause significantly less of a
match than expected. Update with the correct values to get the expected
behavior.
Fixes: 6e9525115b ("CI: add Yocto Project SSTATE Mirror")
Signed-off-by: Jon Mason <jon.mason@arm.com>
On some CI systems, the bitbake server is timing out at 1 mins.
Increase to 5 mins, which hopefully should give enough time without
letting it run forever.
Signed-off-by: Jon Mason <jon.mason@arm.com>
optee-os test xtest needs additional test trusted applications (TA) from
optee-os-ta package to pass. Execution time for ftpm test is around 21
seconds and 596 seconds for optee-test/xtest on an x86_64 build machine.
Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org>
Signed-off-by: Jon Mason <jon.mason@arm.com>
optee-os test xtest needs additional test trusted applications (TA) from
optee-os-ta package to pass. Execution time for ftpm test is around 18
seconds and 430 seconds for optee-test/xtest on an x86_64 build machine.
Signed-off-by: Mikko Rapeli <mikko.rapeli@linaro.org>
Signed-off-by: Jon Mason <jon.mason@arm.com>
There are two recipes in meta-arm-systemready that download ISOs for
testing purposes. Build them in CI to verify that the fetch is
successful.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
We recently switched the CI to not disable ptest, but this breaks builds
that use the GCC binaries built by Arm (external-arm-toolchain). This is
because the external-arm-toolchain recipe can't build packages for the
target, and the standard oe-core gcc recipes assume that they're being
built with themselves and make assumptions, specifically that libunwind
was enabled and headers can be copied directly from the sysroot.
This is a bigger problem that should be solved somehow, but for now we
can just remove ptest in the external-gccarm CI jobs which removes gcc
from the builds (it comes in via elfutils-ptest RDEPENDS).
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
This patch will be merged upstream soon, apply it locally to unblock CI.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add YAML language server comments so that IDEs know what schema to use
for the Kas files.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add a recipe to enable building and deploying the FWU service
implemented in the Trusted Services Project. The FWU service can
help vendors to meet PSA certification requirements.
Signed-off-by: Gyorgy Szing <gyorgy.szing@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add the Yocto Project public SSTATE mirror to its own unique yml file.
This allows for developers to use this to speed up builds, while not
adding in the default case. This "off by default" is because it can add
10s of minutes to each build, which might not be beneficial to those who
are using SSTATE dir locally.
Also, removing the removal ptest distro feature, as this change prevents
an optimal usage of the YP SSTATE mirror (~30% match to ~90% match for
qemuarm64).
Signed-off-by: Jon Mason <jon.mason@arm.com>
These BSPs are now obsolete.
Users of generic-arm64 should use genericarm64 from meta-yocto-bsp.
Users of qemu-generic-arm64 should use sbsa-ref from meta-arm-bsp.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
This is mostly based on the existing qemu-generic-arm64 machine, but by
not being based on the genericarm64 and instead being specifically a
machine to run on the qemu sbsa-ref machine we get to tune differently.
Specifically, this configures sbsa-ref to be a Neoverse N2 (v9), and the
tune is set to match. Another notable difference to qemu-generic-arm64
is that the kernel configuration is at present defconfig. We may wish
to change this in the future to be the same fragmented configuration as
genericarm64.
We have to ignore two testimage parselogs failures: one from NUMA which
will be fixed in a future EDK2 release, and one from efifb where we
should be using the bochsdrm driver instead (further investigation is
needed)
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add the new genericarm64 in meta-yocto-bsp to the CI.
This new BSP is heavily based on the meta-arm generic-arm64 machine, but
with an all-new fragmented kernel configuration.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Some BSPs use a proper initramfs and putting a SSH server into them
via this :append isn't ideal. Adding using += should be sufficient.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add configuration settings to TF-A, OP-TEE and TS SPs needed to get TS
built and run on the fvp-base machine.
Signed-off-by: Gyorgy Szing <gyorgy.szing@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Upstream master and scarthgap have now diverged, so use scarthgap whilst
we prepare for release. At the time of writing there is no scarthgap
branch for meta-clang, so leave that on master.
Signed-off-by: Ross Burton <ross.burton@arm.com>
As of oe-core ba391d3, hashserv lookups will use authentication from the
.netrc file. However, Kas will write invalid netrc files with comments,
which causes bitbake to emit warnings.
This has been fixed in Kas in e700729 but until Kas 4.3.2 is released we
can ignore this warning specifically when checking the logs.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
gcc-arm-none-eabi v11.2 is no longer needed by tf-m. Remove this
version, as there is a newer one available.
Signed-off-by: Jon Mason <jon.mason@arm.com>
The 2 Corstone-1000 kas files files are updated following the
multiconfig changes. The pinned commits have been commented out and
the default branch changed to master to allow the file to build valid
images.
Signed-off-by: Drew Reed <Drew.Reed@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
To ensure the psa and optee tests are included in the initramsfs based
rootfs included within the flash image so the tests can be run.
Signed-off-by: Drew Reed <Drew.Reed@arm.com>
To allow us to continue to ship Corstone-1000 releases that only include
the firmware with the built in Linux image we need a way to build it
outside of the multiconfig builds.
Signed-off-by: Drew Reed <Drew.Reed@arm.com>
By building the Corstone-1000 firmware under the firmware multiconfig we
can also build a minimal standard core image to be mounted in the fvp as
a mass storage device.
To do this we had to enable the MMC card interface in the Corstone-1000
kernel configuration.
Signed-off-by: Drew Reed <Drew.Reed@arm.com>
As we intend to build 2 Corstone-1000 disk images, one for the firmware
in flash and an external mass storage image the existing
corstone1000-image.bb file has been renamed to
corstone1000-flash-firmware-image.bb to make it clear what it's for.
The wks file for specifing the image layout has also been renamed to
make its purpose clearer.
Signed-off-by: Drew Reed <Drew.Reed@arm.com>
We can now use the standard poky distro configured to be small by
switching distrobution and using the standard minimal image
from poky.
To do this we also remove and image configuration options from the
machine config and apply them in the kas files.
Signed-off-by: Drew Reed <Drew.Reed@arm.com>
Setting an API key means we get higher rate limits. Because keys are
private, the key must be set in the environment of the runner.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add a Kas fragment to enable the CVE checker. Disable warnings by
default but show them for the layers in meta-arm, because we only care
about meta-arm issues in this CI.
Explicitly hide kernel warnings as the kernel typically has tens of open
CVEs, and if we're carrying a kernel explicitly then it's typically an
interim kernel between releases.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Extend jobs-to-kas so the first argument is still the GitLab job name,
but allow further arguments to specify extra Kas files to use in
addition.
Then add a variable EXTRA_KAS_FILES to the CI configuration that
defaults to the empty string and pass this to jobs-to-kas.
This lets specific pipeline runs add extra Kas files, for example to use
experimental branches or enable extra features without touching the CI
directly.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Add CI builds for Arm SystemReady Firmware within the fvp-base CI job and a new
Arm SystemReady IR ACS build job. Add the CI kas config for each of these
builds.
The ACS build can be controlled by the ACS_TEST GitLab variable to specify
whether or not to run the testimage. If this variable is not set, the
testimage step will not run. The job tag can be controlled by the ACS_TAG GitLab
variable.
Signed-off-by: Debbie Martin <Debbie.Martin@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Now that we've released 4.3 and branched, we can switch master CI back
to master.
Signed-off-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Upgrade the Arm binary toolchains to the latest version. Of note, the
untarred directory has camelcased the "R" in Rel (which was "rel" in the
previous versions).
Signed-off-by: Jon Mason <jon.mason@arm.com>
