Replace references of WORKDIR with UNPACKDIR where it makes sense to do
so in preparation for changing the default value of UNPACKDIR.
Signed-off-by: Khem Raj <raj.khem@gmail.com>
This patch fixes warnings when useradd-staticids.bbclass is used and
USERADD_PARAM is used to add the user to a group that has not been
explicitly created yet. By adding the GROUPADD_PARAM for the new group
being used the warnings for changing the gid from GID-OLD to GID-NEW
is eliminated.
Warning fixed:
radvd: Changing groupname nogroup's gid from (WXYZ) to (JKLM), verify configuration files!
Signed-off-by: JD Schroeder <sweng5080@gmail.com>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Backport a patch from upstream to fix musl builds
Merged inc file into bb file, makes it easy to use devtool
Signed-off-by: Khem Raj <raj.khem@gmail.com>
This is the result of automated script (0.9.1) conversion:
oe-core/scripts/contrib/convert-overrides.py .
converting the metadata to use ":" as the override character instead of "_".
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
When starting radvd without any configuration the following errors would
be triggered.
"""
root@intel-x86-64:~# systemctl status radvd
● radvd.service - Router advertisement daemon for IPv6
Loaded: loaded (/lib/systemd/system/radvd.service; enabled; vendor preset:
enabled)
Active: inactive (dead)
Condition: start condition failed at Tue 2019-09-24 13:29:36 UTC; 3s ago
└─ ConditionPathExists=/etc/radvd.conf was not met
"""
Normally the user should create and configrue the /etc/radvd.conf
manually. However the radvd provide a example file for redhad located
at "radvd/redhat/radvd.conf.empty". When installing, it would copy
radvd/redhat/radvd.conf.empty to /etc/radvd.conf. Also add this empty
conf here to used as an example of configuration
Signed-off-by: Changqing Li <changqing.li@windriver.com>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
We don't offer /etc/radvd.conf but only radvd.conf.example which would
cause a startup error:
Starting radvd:
* /etc/radvd.conf does not exist or is empty.
Remove update-rc.d settings to make it doesn't start by default.
Signed-off-by: Yi Zhao <yi.zhao@windriver.com>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
* Following error apprear in do configure. Fix it by adding bison-native in DEPENDS.
../radvd-2.17/ylwrap: line 176: yacc: command not found
Signed-off-by: Noor Ahsan <noor_ahsan@mentor.com>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
SECTION has been used inconsistently throughout the recipes in this layer.
Convert them to all use the same convention.
Signed-off-by: Joe MacDonald <joe_macdonald@mentor.com>
1. Fix radvd.service to start daemon correctly.
2. Make the daemon run under 'radvd' user by default.
Signed-off-by: Chen Qi <Qi.Chen@windriver.com>
Signed-off-by: Joe MacDonald <joe_macdonald@mentor.com>
Add systemd service for for radvd.
The unit is disabled by default, just as Fedora20 does.
Signed-off-by: Chen Qi <Qi.Chen@windriver.com>
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
* These recipes all use pkg-config in some way but were missing
dependencies on the tool, this patch adds them.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
When run 'service radvd stop' in case radvd is not started/running,
we'll get warnings like this:
Stopping radvd: no /usr/sbin/radvd found; none killed
/etc/init.d/radvd: warning: cannot restore settings
radvd.
We could by pass these OPs by just check if the service is running
or not so eliminate possible warnings.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Joe MacDonald <joe@deserted.net>
Update radvd to version 1.9.8
* remove change-scanner-dependency.patch which is merged
* add 'status' subcommand for radvd.init
Signed-off-by: Kai Kang <kai.kang@windriver.com>
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
`/etc/init.d/populate-volatile.sh update' only needs to run in case
of an on-target installation. And it should have a prerequisite that
the script is executable.
Signed-off-by: Chen Qi <Qi.Chen@windriver.com>
Signed-off-by: Joe MacDonald <joe@deserted.net>
* This change is only aesthetic (unlike indentation in Python
tasks).
* Some recipes were using tabs.
* Some were using 8 spaces.
* Some were using mix or different number of spaces.
* Make them consistently use 4 spaces everywhere.
* Yocto styleguide advises to use tabs (but the only reason to keep
tabs is the need to update a lot of recipes). Lately this advice
was also merged into the styleguide on the OE wiki.
* Using 4 spaces in both types of tasks is better because it's less
error prone when someone is not sure if e.g.
do_generate_toolchain_file() is Python or shell task and also allows
to highlight every tab used in .bb, .inc, .bbappend, .bbclass as
potentially bad (shouldn't be used for indenting of multiline
variable assignments and cannot be used for Python tasks).
* Don't indent closing quote on multiline variables
we're quite inconsistent wheater it's first character on line
under opening quote or under first non-whitespace character in
previous line.
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
Acked-by: Koen Kooi <koen@dominion.thruhere.net>
* Update to 1.9.1
* Add libdaemon to DEPENDS as needed by 1.9+
* Remove empty config file (not really of much use and there's an
example config in the -doc package anyway)
* Use useradd.bbclass to create user
* Handle hardcoded paths in initscript
* Add LSB headers to initscript (borrowed from openSUSE)
* Set custom LICENSE as it's BSD-Style but not actually one of the
standard BSD variants
* Add LIC_FILES_CHKSUM
* Set SUMMARY (which sets DESCRIPTION)
Signed-off-by: Paul Eggleton <paul.eggleton@linux.intel.com>
Khem Raj
Li Wang
JD Schroeder
Martin Jansa
Zang Ruochen
Changqing Li
Hong Liu
Yi Zhao
Noor Ahsan
Huang Qiyu
Kai Kang
Li xin
Joe MacDonald
Chen Qi
Joe Slater
Richard Purdie
Wenzong Fan
Liang Li
Roy.Li
Paul Eggleton