mirror of
https://git.yoctoproject.org/meta-ti
synced 2026-05-30 07:20:53 +00:00
linux: Add kernel version 3.3.7 for beagleboard
Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com> Signed-off-by: Denys Dmytriyenko <denys@ti.com>
This commit is contained in:
Franklin S. Cooper Jr
committed by
Denys Dmytriyenko
Denys Dmytriyenko
parent
9ff3bd4b3d
commit
233882aa2b
+184
@@ -0,0 +1,184 @@
|
|||||||
|
From 457318d7eff18258b4ef11fb4e4b924d2b5b5bb0 Mon Sep 17 00:00:00 2001
|
||||||
|
From: Russ Dill <Russ.Dill@ti.com>
|
||||||
|
Date: Tue, 8 May 2012 19:49:06 -0700
|
||||||
|
Subject: [PATCH] ARM: OMAP: Cleanup Beagleboard DVI reset gpio
|
||||||
|
|
||||||
|
This removes several boot warnings from board-omap3beagle.c:
|
||||||
|
|
||||||
|
- gpio_request: gpio--22 (DVI reset) status -22
|
||||||
|
- Unable to get DVI reset GPIO
|
||||||
|
|
||||||
|
There is a combination of leftover code and revision confusion.
|
||||||
|
Additionally, xM support is currently a hack.
|
||||||
|
|
||||||
|
For original Beagleboard this removes the double initialization of GPIO
|
||||||
|
170, properly configures it as an output, and wraps the initialization
|
||||||
|
in an if block so that xM does not attempt to request it.
|
||||||
|
|
||||||
|
For Beagleboard xM it removes reference to GPIO 129 which was part
|
||||||
|
of rev A1 and A2 designs, but never functioned. It then properly assigns
|
||||||
|
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
|
||||||
|
hack of initializing it high. Additionally, it uses
|
||||||
|
gpio_set_value_cansleep since this GPIO is connected through i2c.
|
||||||
|
|
||||||
|
Unfortunately, there is no way to tell the difference between xM A2 and
|
||||||
|
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
|
||||||
|
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
|
||||||
|
problems created by this fix.
|
||||||
|
|
||||||
|
v3
|
||||||
|
- Change patch title to include 'ARM: OMAP:'
|
||||||
|
- Actually rename reset_gpio to dvi_reset_gpio
|
||||||
|
|
||||||
|
v2
|
||||||
|
- Rename reset_gpio to dvi_reset_gpio to self document
|
||||||
|
- Use gpio_set_value_cansleep since TWL gpio can sleep
|
||||||
|
- Use gpio_is_valid instead of -EINVAL check
|
||||||
|
|
||||||
|
Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
|
||||||
|
|
||||||
|
Upstream-Status: Submitted
|
||||||
|
* This patch has been submitted for the 3.5 kernel and is
|
||||||
|
being reworked for upstream acceptance.
|
||||||
|
|
||||||
|
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
|
||||||
|
---
|
||||||
|
arch/arm/mach-omap2/board-omap3beagle.c | 49 ++++++++++++++++--------------
|
||||||
|
1 files changed, 26 insertions(+), 23 deletions(-)
|
||||||
|
|
||||||
|
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
|
||||||
|
index 7ffcd28..c9322ac 100644
|
||||||
|
--- a/arch/arm/mach-omap2/board-omap3beagle.c
|
||||||
|
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
|
||||||
|
@@ -81,12 +81,12 @@ static u8 omap3_beagle_version;
|
||||||
|
static struct {
|
||||||
|
int mmc1_gpio_wp;
|
||||||
|
int usb_pwr_level;
|
||||||
|
- int reset_gpio;
|
||||||
|
+ int dvi_reset_gpio;
|
||||||
|
int usr_button_gpio;
|
||||||
|
} beagle_config = {
|
||||||
|
.mmc1_gpio_wp = -EINVAL,
|
||||||
|
.usb_pwr_level = GPIOF_OUT_INIT_LOW,
|
||||||
|
- .reset_gpio = 129,
|
||||||
|
+ .dvi_reset_gpio = -EINVAL,
|
||||||
|
.usr_button_gpio = 4,
|
||||||
|
};
|
||||||
|
|
||||||
|
@@ -124,21 +124,21 @@ static void __init omap3_beagle_init_rev(void)
|
||||||
|
printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
|
||||||
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
|
||||||
|
beagle_config.mmc1_gpio_wp = 29;
|
||||||
|
- beagle_config.reset_gpio = 170;
|
||||||
|
+ beagle_config.dvi_reset_gpio = 170;
|
||||||
|
beagle_config.usr_button_gpio = 7;
|
||||||
|
break;
|
||||||
|
case 6:
|
||||||
|
printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
|
||||||
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
|
||||||
|
beagle_config.mmc1_gpio_wp = 23;
|
||||||
|
- beagle_config.reset_gpio = 170;
|
||||||
|
+ beagle_config.dvi_reset_gpio = 170;
|
||||||
|
beagle_config.usr_button_gpio = 7;
|
||||||
|
break;
|
||||||
|
case 5:
|
||||||
|
printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
|
||||||
|
omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
|
||||||
|
beagle_config.mmc1_gpio_wp = 23;
|
||||||
|
- beagle_config.reset_gpio = 170;
|
||||||
|
+ beagle_config.dvi_reset_gpio = 170;
|
||||||
|
beagle_config.usr_button_gpio = 7;
|
||||||
|
break;
|
||||||
|
case 0:
|
||||||
|
@@ -192,7 +192,7 @@ static struct mtd_partition omap3beagle_nand_partitions[] = {
|
||||||
|
static int beagle_enable_dvi(struct omap_dss_device *dssdev)
|
||||||
|
{
|
||||||
|
if (gpio_is_valid(dssdev->reset_gpio))
|
||||||
|
- gpio_set_value(dssdev->reset_gpio, 1);
|
||||||
|
+ gpio_set_value_cansleep(dssdev->reset_gpio, 1);
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
@@ -200,7 +200,7 @@ static int beagle_enable_dvi(struct omap_dss_device *dssdev)
|
||||||
|
static void beagle_disable_dvi(struct omap_dss_device *dssdev)
|
||||||
|
{
|
||||||
|
if (gpio_is_valid(dssdev->reset_gpio))
|
||||||
|
- gpio_set_value(dssdev->reset_gpio, 0);
|
||||||
|
+ gpio_set_value_cansleep(dssdev->reset_gpio, 0);
|
||||||
|
}
|
||||||
|
|
||||||
|
static struct panel_dvi_platform_data dvi_panel = {
|
||||||
|
@@ -238,12 +238,17 @@ static struct omap_dss_board_info beagle_dss_data = {
|
||||||
|
|
||||||
|
static void __init beagle_display_init(void)
|
||||||
|
{
|
||||||
|
- int r;
|
||||||
|
-
|
||||||
|
- r = gpio_request_one(beagle_dvi_device.reset_gpio, GPIOF_OUT_INIT_LOW,
|
||||||
|
- "DVI reset");
|
||||||
|
- if (r < 0)
|
||||||
|
- printk(KERN_ERR "Unable to get DVI reset GPIO\n");
|
||||||
|
+ if (gpio_is_valid(beagle_config.dvi_reset_gpio)) {
|
||||||
|
+ int r;
|
||||||
|
+
|
||||||
|
+ omap_mux_init_gpio(beagle_config.dvi_reset_gpio, OMAP_PIN_OUTPUT);
|
||||||
|
+ r = gpio_request_one(beagle_config.dvi_reset_gpio,
|
||||||
|
+ GPIOF_OUT_INIT_LOW, "DVI reset");
|
||||||
|
+ if (r < 0)
|
||||||
|
+ printk(KERN_ERR "Unable to get DVI reset GPIO\n");
|
||||||
|
+ else
|
||||||
|
+ beagle_dvi_device.reset_gpio = beagle_config.dvi_reset_gpio;
|
||||||
|
+ }
|
||||||
|
}
|
||||||
|
|
||||||
|
#include "sdram-micron-mt46h32m32lf-6.h"
|
||||||
|
@@ -272,7 +277,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
|
||||||
|
{
|
||||||
|
int r;
|
||||||
|
|
||||||
|
- if (beagle_config.mmc1_gpio_wp != -EINVAL)
|
||||||
|
+ if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
|
||||||
|
omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
|
||||||
|
mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
|
||||||
|
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
|
||||||
|
@@ -297,11 +302,14 @@ static int beagle_twl_gpio_setup(struct device *dev,
|
||||||
|
if (r)
|
||||||
|
pr_err("%s: unable to configure nDVI_PWR_EN\n",
|
||||||
|
__func__);
|
||||||
|
- r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
|
||||||
|
- "DVI_LDO_EN");
|
||||||
|
+
|
||||||
|
+ r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_LOW,
|
||||||
|
+ "DVI_PU");
|
||||||
|
if (r)
|
||||||
|
- pr_err("%s: unable to configure DVI_LDO_EN\n",
|
||||||
|
- __func__);
|
||||||
|
+ pr_err("%s: unable to get DVI_PU GPIO\n", __func__);
|
||||||
|
+ else
|
||||||
|
+ beagle_dvi_device.reset_gpio = gpio + 2;
|
||||||
|
+
|
||||||
|
} else {
|
||||||
|
/*
|
||||||
|
* REVISIT: need ehci-omap hooks for external VBUS
|
||||||
|
@@ -310,7 +318,6 @@ static int beagle_twl_gpio_setup(struct device *dev,
|
||||||
|
if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
|
||||||
|
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
|
||||||
|
}
|
||||||
|
- beagle_dvi_device.reset_gpio = beagle_config.reset_gpio;
|
||||||
|
|
||||||
|
gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
|
||||||
|
"nEN_USB_PWR");
|
||||||
|
@@ -532,10 +539,6 @@ static void __init omap3_beagle_init(void)
|
||||||
|
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
|
||||||
|
mt46h32m32lf6_sdrc_params);
|
||||||
|
|
||||||
|
- omap_mux_init_gpio(170, OMAP_PIN_INPUT);
|
||||||
|
- /* REVISIT leave DVI powered down until it's needed ... */
|
||||||
|
- gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
|
||||||
|
-
|
||||||
|
usb_musb_init(NULL);
|
||||||
|
usbhs_init(&usbhs_bdata);
|
||||||
|
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
|
||||||
|
--
|
||||||
|
1.7.0.4
|
||||||
|
|
||||||
+169
@@ -0,0 +1,169 @@
|
|||||||
|
From bce492c04ba8fc66a4ea0a52b181ba255daaaf54 Mon Sep 17 00:00:00 2001
|
||||||
|
From: Govindraj.R <govindraj.raja@ti.com>
|
||||||
|
Date: Tue, 17 Apr 2012 10:35:47 -0700
|
||||||
|
Subject: [PATCH] ARM: OMAP2+: UART: Fix incorrect population of default uart pads
|
||||||
|
|
||||||
|
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
|
||||||
|
wrongly added muxing of default pads for all uarts. This causes
|
||||||
|
breakage on multiple boards using uart pins for alternate functions.
|
||||||
|
|
||||||
|
For example, on zoom3 random oopses can be seen with nfsroot as
|
||||||
|
the smsc911x ethernet FIFO timings on GPMC bus are controlled
|
||||||
|
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
|
||||||
|
pads to uart4 functionality as commit 7496ba3 was doing.
|
||||||
|
|
||||||
|
Not all boards tend to use all uarts and most of unused uart pins
|
||||||
|
are muxed for other purpose. This commit breaks the modules which
|
||||||
|
where trying to use unused uart pins on their boards.
|
||||||
|
|
||||||
|
So remove the default pad muxing. Note that this is not a complete
|
||||||
|
fix, as we now rely on bootloader set muxing for the uart wake-up
|
||||||
|
events. Further patching is needed to enable wake-up events for
|
||||||
|
uarts that are already muxed to uart mode.
|
||||||
|
|
||||||
|
Upstream-Status: Backport
|
||||||
|
* Backported from commit bce492c0 in linux mainline
|
||||||
|
|
||||||
|
Cc: Felipe Balbi <balbi@ti.com>
|
||||||
|
Cc: Kevin Hilman <khilman@ti.com>
|
||||||
|
Acked-by: Russ Dill <russ.dill@gmail.com>
|
||||||
|
Reported-by: Tony Lindgren <tony@atomide.com>
|
||||||
|
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
|
||||||
|
[tony@atomide.com: updated comments to describe oops on zoom3]
|
||||||
|
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
||||||
|
---
|
||||||
|
arch/arm/mach-omap2/serial.c | 116 ------------------------------------------
|
||||||
|
1 files changed, 0 insertions(+), 116 deletions(-)
|
||||||
|
|
||||||
|
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
|
||||||
|
index 0cdd359..2e351f5 100644
|
||||||
|
--- a/arch/arm/mach-omap2/serial.c
|
||||||
|
+++ b/arch/arm/mach-omap2/serial.c
|
||||||
|
@@ -120,124 +120,8 @@ static void omap_uart_set_smartidle(struct platform_device *pdev) {}
|
||||||
|
#endif /* CONFIG_PM */
|
||||||
|
|
||||||
|
#ifdef CONFIG_OMAP_MUX
|
||||||
|
-static struct omap_device_pad default_uart1_pads[] __initdata = {
|
||||||
|
- {
|
||||||
|
- .name = "uart1_cts.uart1_cts",
|
||||||
|
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart1_rts.uart1_rts",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart1_tx.uart1_tx",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart1_rx.uart1_rx",
|
||||||
|
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
|
||||||
|
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- .idle = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
-};
|
||||||
|
-
|
||||||
|
-static struct omap_device_pad default_uart2_pads[] __initdata = {
|
||||||
|
- {
|
||||||
|
- .name = "uart2_cts.uart2_cts",
|
||||||
|
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart2_rts.uart2_rts",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart2_tx.uart2_tx",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart2_rx.uart2_rx",
|
||||||
|
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
|
||||||
|
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- .idle = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
-};
|
||||||
|
-
|
||||||
|
-static struct omap_device_pad default_uart3_pads[] __initdata = {
|
||||||
|
- {
|
||||||
|
- .name = "uart3_cts_rctx.uart3_cts_rctx",
|
||||||
|
- .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart3_rts_sd.uart3_rts_sd",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart3_tx_irtx.uart3_tx_irtx",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart3_rx_irrx.uart3_rx_irrx",
|
||||||
|
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
|
||||||
|
- .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
|
||||||
|
- .idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
-};
|
||||||
|
-
|
||||||
|
-static struct omap_device_pad default_omap36xx_uart4_pads[] __initdata = {
|
||||||
|
- {
|
||||||
|
- .name = "gpmc_wait2.uart4_tx",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "gpmc_wait3.uart4_rx",
|
||||||
|
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
|
||||||
|
- .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE2,
|
||||||
|
- .idle = OMAP_PIN_INPUT | OMAP_MUX_MODE2,
|
||||||
|
- },
|
||||||
|
-};
|
||||||
|
-
|
||||||
|
-static struct omap_device_pad default_omap4_uart4_pads[] __initdata = {
|
||||||
|
- {
|
||||||
|
- .name = "uart4_tx.uart4_tx",
|
||||||
|
- .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
- {
|
||||||
|
- .name = "uart4_rx.uart4_rx",
|
||||||
|
- .flags = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
|
||||||
|
- .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
|
||||||
|
- .idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
|
||||||
|
- },
|
||||||
|
-};
|
||||||
|
-
|
||||||
|
static void omap_serial_fill_default_pads(struct omap_board_data *bdata)
|
||||||
|
{
|
||||||
|
- switch (bdata->id) {
|
||||||
|
- case 0:
|
||||||
|
- bdata->pads = default_uart1_pads;
|
||||||
|
- bdata->pads_cnt = ARRAY_SIZE(default_uart1_pads);
|
||||||
|
- break;
|
||||||
|
- case 1:
|
||||||
|
- bdata->pads = default_uart2_pads;
|
||||||
|
- bdata->pads_cnt = ARRAY_SIZE(default_uart2_pads);
|
||||||
|
- break;
|
||||||
|
- case 2:
|
||||||
|
- bdata->pads = default_uart3_pads;
|
||||||
|
- bdata->pads_cnt = ARRAY_SIZE(default_uart3_pads);
|
||||||
|
- break;
|
||||||
|
- case 3:
|
||||||
|
- if (cpu_is_omap44xx()) {
|
||||||
|
- bdata->pads = default_omap4_uart4_pads;
|
||||||
|
- bdata->pads_cnt =
|
||||||
|
- ARRAY_SIZE(default_omap4_uart4_pads);
|
||||||
|
- } else if (cpu_is_omap3630()) {
|
||||||
|
- bdata->pads = default_omap36xx_uart4_pads;
|
||||||
|
- bdata->pads_cnt =
|
||||||
|
- ARRAY_SIZE(default_omap36xx_uart4_pads);
|
||||||
|
- }
|
||||||
|
- break;
|
||||||
|
- default:
|
||||||
|
- break;
|
||||||
|
- }
|
||||||
|
}
|
||||||
|
#else
|
||||||
|
static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {}
|
||||||
|
--
|
||||||
|
1.7.0.4
|
||||||
|
|
||||||
File diff suppressed because it is too large
Load Diff
@@ -0,0 +1,41 @@
|
|||||||
|
DESCRIPTION = "Linux 3.3 stable kernel release"
|
||||||
|
SECTION = "kernel"
|
||||||
|
|
||||||
|
LICENSE = "GPLv2"
|
||||||
|
LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
|
||||||
|
|
||||||
|
DEFAULT_PREFERENCE = "-1"
|
||||||
|
|
||||||
|
COMPATIBLE_MACHINE = "beagleboard"
|
||||||
|
|
||||||
|
inherit kernel
|
||||||
|
|
||||||
|
KERNEL_IMAGETYPE = "uImage"
|
||||||
|
|
||||||
|
# The main PR is now using MACHINE_KERNEL_PR, for beagleboard see
|
||||||
|
# conf/machine/include/omap3.inc
|
||||||
|
MACHINE_KERNEL_PR_append = "a+gitr${SRCREV}"
|
||||||
|
|
||||||
|
BRANCH = "linux-3.3.y"
|
||||||
|
SRCREV = "v3.3.7"
|
||||||
|
|
||||||
|
SRC_URI = "git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git;protocol=git;branch=${BRANCH} \
|
||||||
|
file://defconfig"
|
||||||
|
|
||||||
|
# These are patches that are making their way upstream or are pulled back
|
||||||
|
# from upstream trees to make the stable kernel work without regressions.
|
||||||
|
# These patches should clear out when moving to the next stable kernel
|
||||||
|
# minor version. i.e. 3.y.
|
||||||
|
SRC_URI_append_beagleboard = " file://0001-ARM-OMAP-Cleanup-Beagleboard-DVI-reset-gpio.patch \
|
||||||
|
file://0001-ARM-OMAP2-UART-Fix-incorrect-population-of-default-u.patch \
|
||||||
|
"
|
||||||
|
|
||||||
|
S = "${WORKDIR}/git"
|
||||||
|
|
||||||
|
EXTRA_OEMAKE = "${PARALLEL_MAKE}"
|
||||||
|
|
||||||
|
# Create the uImage symlink in /boot since by default beagleboard looks into
|
||||||
|
# the /boot directory for the uImage file instead of the first partition.
|
||||||
|
do_install_append_beagleboard() {
|
||||||
|
cd ${D}/${KERNEL_IMAGEDEST} && ln -sf uImage-${KERNEL_VERSION} uImage
|
||||||
|
}
|
||||||
Reference in New Issue
Block a user