The SK-Ethernet-DC01 Add-On Ethernet Card for AM62A-SK board supports
RGMII mode.
Add overlay to enable the second CPSW3G port in RGMII-RXID mode with the
Add-On Ethernet Card.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the MCSPI loopback overlay file for J784S4 EVM which helps
users to enable MCU-MAIN MCSPI loopback applications, even though
the overlay is named j7200-mcspi-loopback.dtbo, same can be used
for testing on other J7 platforms as well.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the MCSPI loopback overlay file for J721S2 EVM which helps
users to enable MCU-MAIN MCSPI loopback applications, even though
the overlay is named j7200-mcspi-loopback.dtbo, same can be used
for testing on other J7 platforms as well.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the MCSPI loopback overlay file for J721E EVM which helps
users to enable MCU-MAIN MCSPI loopback applications, even though
the overlay is named j7200-mcspi-loopback.dtbo, same can be used
for testing on other J7 platforms as well.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J784S4 SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J721S2 SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J721E SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J7200 SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The AM69 SK has PWM output pins connected to its RPi header. Add
overlay file to enable PWM pins.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the basic J784S4 HS-FS configuration.
* Add configurations to support both HS-FS and GP keeping GP as default.
* Add ti-sci-firmware overrides for HS-FS.
* Remove evm conf file inclusion in hs-evm conf.
* Add j784s4 hs-evm specific config to hs-evm conf.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62A configuration
- Add machine conf for AM62A.
- The wic images will boot on AM62A HS-FS devices by default. The sysfw image for GP and HS-SE will be packaged in the wic image as tiboot3-am62ax-gp-evm.bin and tiboot3-am62ax-hs-evm.bin respectively.
- Add ti-sci-firmware overrides.
- Sign ATF, OPTEE and RTOS Firmware.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the basic J721S2 HS-FS configuration.
- Add configurations to support both HS-FS and GP keeping GP
as default.
- Add ti-sci-firmware overrides for HS-FS.
- Remove evm conf file inclusion in hs-evm conf.
- Add j721s2 hs-evm specific config to hs-evm conf.
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62x LP HS-FS configuration
- Add machine conf for AM62x LP HS-FS.
- The wic images will boot on AM62x LP HS-FS devices by default. The sysfw image for HS-SE will be packaged in the wic image as tiboot3-am62x-hs-evm.bin.
- Add ti-sci-firmware overrides.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62x HS-FS configuration
- Add machine conf for AM62x HS-FS.
- The wic images will boot on AM62x HS-FS devices by default. The sysfw image for GP and HS-SE will be packaged in the wic image as tiboot3-am62x-gp-evm.bin and tiboot3-am62x-hs-evm.bin respectively.
- Add ti-sci-firmware overrides.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
K3 platforms include the FIT image-based kernel by default. The bootloader
loads the kernel and DTB from the FIT image. The DTB/DTBOs are added to the
FIT image but the load address is not included in the image section of
each DTB/DTBO. This load address is determined by the LOADADDRESS macros
in the kernel-fitmage class.
Hence, define the RD/DTB/DTBOs LOADADDRESS and OFFSET macros in the K3 common
include, and remove those macros defined in the K3 board specific config files.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The AM68 SK has PWM output pins connected to its RPi headers. Add
overlay file to enable PWM pins.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the overlay files for AM69 SK:
1. Fusion board (For FPDLink-III cameras).
2. IMX390 FPDLink-III camera module that includes both the CM and
RCM type of modules.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62x HS-SE configuration.
- Add machine conf for AM62x HS-SE.
- The wic images will boot on AM62x GP devices by default. To boot on AM62x HS-SE, simply switch out the SYSFW image:
$ cd /mnt/sd-card/boot
$ mv tiboot3-am62x-hs-evm.bin tiboot3.bin
- Add ti-sci-firmware overrides.
- Add support to sign ATF and OPTEE.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the overlay files, over AM68 SK, for the following:
1. Fusion board (For FPDLink-III cameras).
2. IMX390 FPDLink-III camera module which includes both the CM and
RCM type of modules.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The extension for OV5640 overlay is incorrect. Therefore, update the
correct extension to build the overlay with .dtbo
Fixes: f67e9805 ("conf: machine: j721s2: Add AM68 SK specific dtb and dtbo to KERNEL_DEVICETREE")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
AM69 Starter Kit is a single board designed based on TI's AM69 SOC
providing advanced system integration in automotive ADAS applications,
autonomous mobile robot and edge AI applications. Add support
for the same to include the board dtb file into the root filesystem.
Add DT overlays support for the following features on AM69 SK:
* Add DTBO entry to support OV5640 camera
* Add DTBO entry to support RPi(IMX219) camera
* Add DTBO entry for the DDR memory carveout.
[1]:https://www.ti.com/lit/zip/spruj52
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
IMX390 is a 2MP FPDLink-III raw camera. This sensor was originally
targeted for J7-based devices, but AM62A can re-use the existing
overlays. Both the CM and RCM type of modules are supported.
As AM62A only has one CSI-RX port, we only use 4 out of the 8 total
FPDLink ports on the fusion board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
AM68 Starter Kit is a low cost, small form factor board designed for
TI's AM68/J721S2 SoC[1] which is optimized to provide best in class performance
for industrial applications. Add DTB entry for the same.
AM68 SK features camera support with MIPI(OV5640) and RPi(IMX219) connectors.
Add DTBO for the same. Also, add DTBO entry for the DDR memory carveout.
[1]:http://www.ti.com/lit/zip/spruj28
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the following overlay files on AM62A SK:
1. Fusion board (For FPDLink-III cameras)
2. OV2312 FPDLink camera module
3. IMX219 RPi-compatible camera module
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
With a recent patch to the TI kernel that includes debug symbols,
the vmlinux.gz file grew in size that impacted the testing.
This file is not needed to be in the final image so remove it
from the list.
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Machine conf for J784S4 HS platform.
Used J721S2 hs as reference.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Change the OP-TEE flavour from default k3-j721e to k3-j784s4
as sa3ul support for j784s4 is upstreamed in OP-TEE and we
can use the same settings in j721s2 to access TRNG.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the new OP-TEE flavour for J784S4 instead of default k3-j721e.
The TI-SCI ID for MCU domain sa2ul/sa3ul are not the same for
J721E and J784S4. So a new flavour is added in upstream OP-TEE.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Serial console in J721S2/J784S4 EVM config was set to ttyS10. It should be ttyS2.
This caused sysv based systems (eg, tiny) to apparently hang because of no login prompt.
This didn't show up as a problem on systemd systems (eg, default) because systemd will
automatically setup a serial tty with the console option passed in on the kernel command line
(using console=...), which U-Boot correctly passes in as ttyS2 for J721S2/J784S4.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The supported device types depends on the SoC, not on any specific
board or EVM. Any board can be populated with any of the 3 supported
AM64x types. Move these into the AM64x common include.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
AM64x devices will only be available as SR2.0 HS-FS. Set this as the
default type provided by the SDK. To allow SR2.0 HS-SE to continue to
boot, like we did with GP, we add an extra machine to build SR2.0 HS-SE
SYSFW. To use on SR2.0 HS-SE boards simply switch out the SYSFW image:
$ cd /mnt/sd-card/boot
$ mv tiboot3-am64x_sr2-hs-evm.bin tiboot3.bin
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
This platform is similar to the currently supported am62xx-evm, except
that we currently need new defconfigs for u-boot and new dtbs in the
filesystem.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Hari Nagalla <hnagalla@ti.com>
Cc: Andrew Davis <afd@ti.com>
Cc: Praneeth Bajjuri <praneeth@ti.com>
Cc: Ryan Eatmon <reatmon@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
In the latest U-Boot the HS images for AM64x have been renamed to the
default names, and the GP have been changed to *_unsigned. Remove
the overrides to pull the now default HS images.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The HS-SE AM64xx machine can now be run on GP devices and built without
needing the TI_SECURE_DEV_PKG for the same. AM64xx will only be available
in the HS-FS type going forward. Make the HS-SE the default and remove
the original GP machine.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
FIT Image based kernels are valid for all K3 devices, not just HS, deploy
this kernel image type by default so it doesn't have to be appended on
a per-device-type basis.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Use multiconfig to generate a GP SYSFW image. This allows the HS SDK
to be used on GP boards by simply switching out the SYSFW image:
$ cd /mnt/sd-card/boot
$ mv tiboot3-am64x-gp-evm.bin tiboot3.bin
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Update to the latest commit of ti-u-boot-2021.01.
As part of this U-Boot update the non-HS AM64x-evm defconfig was removed.
This is okay as building this defconfig without defining TI_SECURE_DEV_PKG
will still result in usable binaries for the non-HS devices. Use the
HS defconfig for both the HS and non-HS machines.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The K3 TI_SECURE_DEV_PKG is the same for all devices, move this out
of each machine file and into the common K3 includes. This doesn't
have any effect on the GP machines as they make no use of it.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Going forward, the combined tiboot3.bin is going to be the standard. Only
AM65x and J721e will still use the split boot.
Set DEPENDS and EXTRA_OEMAKE for combined boot and override only for the
two split boot platforms. This makes it easier to add new platforms and
simplifies deployment logic.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Siddharth Vadapalli
Vaishnav Achath
Bhavya Kapoor
Dasnavis Sabiya
Sai Sree Kartheek Adivi
Sinthu Raja
Chirag Shilwant
Aradhya Bhatia
Jai Luthra
Denys Dmytriyenko
Paresh Bhagat
Ryan Eatmon
Zachary Booth
Manorit Chawdhry
Jayesh Choudhary
Andrew Davis
Anand Gadiyar