diff --git a/README.md b/README.md index f0e7dcd..8e37040 100644 --- a/README.md +++ b/README.md @@ -64,48 +64,47 @@ Raspberry Pi implementation should be connected to A4988, DRV8825 or any other stepper motor drivers with DIR and STEP pin inputs. Default config is created for Raspberry Pi 2-3 and this wiring config: -| Circuit | RPi pin | RAMPS pin | Note | -|-----------------|-------------|--------------------------|------------------| -| X step | GPIO21 | A0 | | -| X dir | GPIO20 | A1 | | -| steppers enable | GPIO26 | A2, A8, D24, D34, D38 | all steppers | -| Y step | GPIO16 | A6 | | -| Y dir | GPIO19 | A7 | | -| Z dir | GPIO13 | D48 | | -| Z step | GPIO12 | D46 | | -| E1 step | GPIO6 | D36 | reserve | -| E1 dir | GPIO5 | D34 | reserve | -| E0 dir | GPIO7 | D28 | | -| E0 step | GPIO8 | D26 | | -| Z max | GPIO11 | D19 | | -| Z min | GPIO25 | D18 | | -| Y max | GPIO9 | D15 | | -| Y min | GPIO10 | D14 | | -| X max | GPIO24 | D2 | | -| X min | GPIO23 | D3 | | -| heater bed | GPIO22 | D8 | | -| heater 2 | GPIO27 | D9 | uses for fan | -| heater 1 | GPIO18 | D10 | | -| ser 1 | GPIO17 | D11 | reserve | -| ser 2 | GPIO15 | D6 | reserve | -| ser 3 | GPIO4 | D5 | reserve | -| ser 4 | GPIO14 | D4 | reserve | -| I2C SCL | GPIO3 | - | to ads111x | -| I2C SDA | GPIO2 | - | to ads111x | -| ads1115 ch0 | - | A15 | heater 2 - nc | -| ads1115 ch1 | - | A14 | bed sensor | -| ads1115 ch2 | - | A13 | extruder sensor | -| ads1115 ch3 | - | - | not connected | +| Circuit name | RPi pin name | RAMPSv1.4 board pin name | Note | +|-----------------|--------------|--------------------------|-----------------| +| X step | GPIO21 | A0 | | +| X dir | GPIO20 | A1 | | +| steppers enable | GPIO26 | A2, A8, D24, D34, D38 | all steppers | +| Y step | GPIO16 | A6 | | +| Y dir | GPIO19 | A7 | | +| Z dir | GPIO13 | D48 | | +| Z step | GPIO12 | D46 | | +| E1 step | GPIO6 | D36 | reserve | +| E1 dir | GPIO5 | D34 | reserve | +| E0 dir | GPIO7 | D28 | | +| E0 step | GPIO8 | D26 | | +| Z max | GPIO11 | D19 | | +| Z min | GPIO25 | D18 | | +| Y max | GPIO9 | D15 | | +| Y min | GPIO10 | D14 | | +| X max | GPIO24 | D2 | | +| X min | GPIO23 | D3 | | +| heater bed | GPIO22 | D8 | | +| heater 2 | GPIO27 | D9 | uses for fan | +| heater 1 | GPIO18 | D10 | | +| ser 1 | GPIO17 | D11 | reserve | +| ser 2 | GPIO15 | D6 | reserve | +| ser 3 | GPIO4 | D5 | reserve | +| ser 4 | GPIO14 | D4 | reserve | +| I2C SCL | GPIO3 | - | to ads111x | +| I2C SDA | GPIO2 | - | to ads111x | +| ads1115 ch0 | - | A15 | heater 2 - nc | +| ads1115 ch1 | - | A14 | bed sensor | +| ads1115 ch2 | - | A13 | extruder sensor | +| ads1115 ch3 | - | - | not connected | So having Raspberry Pi connected this way, there is no need to configure pin map for project. [RAMPS v1.4](http://reprap.org/wiki/RAMPS_1.4) board can be used for this purpose. Full reference circuit diagram and photos of -assembled controller(click to enlarge): -[![circuit_small](https://user-images.githubusercontent.com/8740775/28233810-40773186-6902-11e7-8496-5750babfcf44.jpg)](https://user-images.githubusercontent.com/8740775/28233650-d64060e0-6900-11e7-8605-6475384fd2f7.png) -[![sample_front_small](https://user-images.githubusercontent.com/8740775/28233812-407820c8-6902-11e7-8de1-35c03509c0e5.jpg)](https://user-images.githubusercontent.com/8740775/28233649-d6402800-6900-11e7-8dca-cd35c8292e0c.jpg) -[![sample_back_small](https://user-images.githubusercontent.com/8740775/28233879-db96ea1c-6902-11e7-9298-11150476084b.jpg)](https://user-images.githubusercontent.com/8740775/28233648-d63fa0c4-6900-11e7-8fab-2055e035a6cb.jpg) -[![sample_mounted_small](https://user-images.githubusercontent.com/8740775/28233811-40777e8e-6902-11e7-8899-5991860d182c.jpg)](https://user-images.githubusercontent.com/8740775/28233652-d65f82ea-6900-11e7-9e80-d8b0c9238f95.jpg) - +assembled controller(click to enlarge): +[![circuit small](https://user-images.githubusercontent.com/8740775/28233810-40773186-6902-11e7-8496-5750babfcf44.jpg)](https://user-images.githubusercontent.com/8740775/28233650-d64060e0-6900-11e7-8605-6475384fd2f7.png) +[![sample front small](https://user-images.githubusercontent.com/8740775/28233812-407820c8-6902-11e7-8de1-35c03509c0e5.jpg)](https://user-images.githubusercontent.com/8740775/28233649-d6402800-6900-11e7-8dca-cd35c8292e0c.jpg) +[![sample back small](https://user-images.githubusercontent.com/8740775/28233879-db96ea1c-6902-11e7-9298-11150476084b.jpg)](https://user-images.githubusercontent.com/8740775/28233648-d63fa0c4-6900-11e7-8fab-2055e035a6cb.jpg) +[![sample mounted small](https://user-images.githubusercontent.com/8740775/28233811-40777e8e-6902-11e7-8899-5991860d182c.jpg)](https://user-images.githubusercontent.com/8740775/28233652-d65f82ea-6900-11e7-9e80-d8b0c9238f95.jpg) # Usage Just clone this repo and run `./pycnc` from repo root. It will start in diff --git a/setup.py b/setup.py index 879a886..47d1bab 100755 --- a/setup.py +++ b/setup.py @@ -9,7 +9,7 @@ except(IOError, ImportError): from setuptools import setup, find_packages setup( name="pycnc", - version="1.0.0", + version="1.1.0", packages=find_packages(), scripts=['pycnc'],