overlay_map.dtb arranges that when config.txt requests "vc4-kms-v3d"
the rpi4 will actually load "vc4-kms-v3d-pi4" and fixups like that.
It is present on the official distros, and must be put into the
overlays subdirectory in the boot partition.
For a detailed description of the overlay_map.dts file see:
https://www.raspberrypi.org/documentation/configuration/device-tree.md#part2.2.10
vc4-kms-v3d-pi4 is required for the arm based kms driver on the rpi4.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
In theory, this would allow one to use the official 7-inch touchscreen
in combination with the (non-firmware) kms driver by adding the
following lines to config.txt:
ignore_lcd=1
dtoverlay=vc4-kms-v3d
dtoverlay=vc4-kms-dsi-7inch
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
The rpi_arm64 configuration supports both Raspberry Pi 3 & 4 in 64-bit
mode. Switching to this config is a small step towards supporting a
unified build for these targets.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Before this patch, use of RPI_EXTRA_CONFIG += in a local.conf would overwrite
the needed 'arm_64bit=1' defined in the core recipes. The net result would be
a system that did not boot.
This patch fixes the assignment of 'arm_64bit=1' even if RPI_EXTRA_CONFIG
has been set elsewhere.
Signed-off-by: matthew@thespencers.me.uk
To allow other layers to easily provide a default kernel preference to
use with the Raspberry Pi MACHINEs, switch to use the ??= assignment
operator for setting the default kernel and the device tree value in
this layer.
This change is motivated by enabling Xen support in meta-virtualization
to use the raspberrypi4-64 MACHINE definition from this layer with the
Yocto Linux kernels.
Signed-off-by: Christopher Clark <christopher.w.clark@gmail.com>
Added imx219.dtbo file in the overlays, and added dtoverlay in
/boot/config.txt define based.
To enable Sony Raspberry pi camera imx219 sensor, need to set
the variable RASPBERRYPI_CAMERA_V2 as 1.
In future, we can add any camera overlays here to support and
use them with libcamera.
Signed-off-by: Madhavan Krishnan <madhavan.krishnan@linaro.org>
rpi kernel spits out additional errors in kernel logs which should be
ignored, there is no easy way to extend parselogs testcase other than
inheriting it into another testcase and use that testcase instead
Signed-off-by: Khem Raj <raj.khem@gmail.com>
The raspberry pi 4 variant has a BCM2711 chip, however it still
uses the same boot files as the BCM2835 used in previous generations.
This change generalizes the naming of the directory generated in the
$DEPLOY_DIR to avoid the implication that the files are only
meant for the BCM2835.
Signed-off-by: Jeff Ithier <ithijme@gmail.com>
The device tree only supports a single CAN interface. This prevents
compatiblity with dual-CAN boards like the PiCAN2 Duo.
The mcp2515-can1 device tree blob for overlay was added to RPI_KERNEL_DEVICETREE_OVERLAYS in order to support dual-CAN hats.
Signed-off-by: Colin McAllister <colinmca242@gmail.com>
As per the example in the bsp-guide, and the qemu and other machine
configs. Assists when running virtualized, where serial console
device can differ.
Signed-off-by: Christopher Clark <christopher.w.clark@gmail.com>
Add kernel modules gpio-ir and gpio-ir-tx to variable
MACHINE_ESSENTIAL_EXTRA_RRECOMMENDS if ENABLE_IR is set to 1.
Variable ENABLE_IR enables infrared support (for LIRC). This
change affects images based on packagegroup-core-boot, including
the core-image-minimal image.
For other images (based on packagegroup-base) kernel modules
are provide through variable MACHINE_EXTRA_RRECOMMENDS.
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
Add device tree binary overlays gpio-ir-tx and gpio-ir-tx to
support peripherals for sending and receiving infrared signals.
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
Add kernel modules i2c-dev and i2c-bcm2708 to variable
MACHINE_ESSENTIAL_EXTRA_RRECOMMENDS if ENABLE_I2C is set to 1.
This affects images based on packagegroup-core-boot, including
the core-image-minimal image.
For other images (based on packagegroup-base) kernel modules
are provide through variable MACHINE_EXTRA_RRECOMMENDS.
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
Add kernel modules, including i2c-dev and i2c-bcm2708, to variable
MACHINE_ESSENTIAL_EXTRA_RRECOMMENDS. This way kernel modules will
be present in all images based on packagegroup-core-boot,
including the core-image-minimal image.
Otherwise, if modules, are in variable MACHINE_EXTRA_RRECOMMENDS
they will be added only in images based on packagegroup-base,
which does not include the core-image-minimal or
core-image-full-cmdline images.
Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
pi3-disable-bt is renamed to disable-bt and pi3-miniuart-bt is renamed
to miniuart-bt in 2014, now with 5.4 these are not recognised anymore
and miniuart-bt and disable-bt are already part of RPI_KERNEL_DEVICETREE_OVERLAYS
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Add u-boot-default-script to the PROVIDES variable to make easier to
replace boot script in another layer just by changing
PREFERRED_PROVIDER_u-boot-default-script variable. Set rpi-u-boot-scr as
the default provider for meta-raspberrypi.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
This change moves the default image for all rpi machines.
We moved from rpi-sdimg to wic.bz2.
Also enable wic.bmap image generation.
From the documentation in [1], Bmaptool is a generic tool
for creating the block map (bmap) for a file and copying
files using the block map. The idea is that large files,
like raw system image files, can be copied or flashed a
lot faster and more reliably with bmaptool than with
traditional tools, like "dd" or "cp".
Example:
$: sudo bmaptool copy <image-name>.wic.xz /dev/<your-block-device>
[1] - https://github.com/intel/bmap-tools
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Add support for the Adafruit PiTFT Plus 320x240 2.8" TFT with
Capacitive Touchscreen, using the same patterns used for the other
versions of the PiTFT screens.
Signed-off-by: Erik Botö <erik.boto@gmail.com>
Since we enabled vc4graphics by default[1], there is no easy way to disable
it if needed. This patch introduces a variable (DISABLE_VC4GRAPHICS)
which when set to '1' will not add 'vc4graphics' to MACHINE_FEATURES
forcing the old behaviour.
One could use it in 'local.conf' for example.
[1] https://github.com/agherzan/meta-raspberrypi/pull/417
Signed-off-by: Andrei Gherzan <andrei@gherzan.ro>
Vc4graphics enables drm backend on wayland Compositor (weston & westeros)
Appending vc4graphics machine feature to use mesa drivers for OpenGL and
V4l2 for video.
Signed-off-by: Riyaz <Riyaz.l@ltts.com>
Currently, we use vc4-kms-v3d as the default overlay for VC4 but this
seems to break vc4 at runtime on RPi4. Change this to vc4-fkms-v3d for
now as this is the default Raspbian ons as well.
Signed-off-by: Andrei Gherzan <andrei@gherzan.ro>
sss22213
Pierre-Jean Texier
Khem Raj
Mike Looijmans
Aaron Shaw
Martin Jansa
Paul Barker
Matt Spencer
Christopher Clark
Madhavan Krishnan
Pierre-Jean Texier
Jeff Ithier
colin
Leon Anavi
Drew Moseley
Fabio Berton
Orne Brocaar
Erik Botö
Ricardo Salveti
Allen Wild
Andrei Gherzan
Riyaz