The patch was dropped with 3.17 update:
https://git.yoctoproject.org/meta-ti/commit/?h=dunfell&id=f8182afdcfe427865707077d353359827f1ff6bf
But the patch is still needed for internal OE-built toolchain to pass
sysroot, otherwise libgcc.a cannot be found:
| aarch64-oe-linux-ld.bfd: cannot find libgcc.a: No such file or directory
The older version from meta-arm/dunfell no longer applies, so copy a newer
version of the patch locally.
Signed-off-by: Denys Dmytriyenko <denys@konsulko.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
main-r5f0_0-fw was pointing to pdk-ipc binary, while it should be
pointing to ethfw one for j784s4-evm, j784s4-hs-evm
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The SK-Ethernet-DC01 Add-On Ethernet Card for AM62A-SK board supports
RGMII mode.
Add overlay to enable the second CPSW3G port in RGMII-RXID mode with the
Add-On Ethernet Card.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the MCSPI loopback overlay file for J784S4 EVM which helps
users to enable MCU-MAIN MCSPI loopback applications, even though
the overlay is named j7200-mcspi-loopback.dtbo, same can be used
for testing on other J7 platforms as well.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the MCSPI loopback overlay file for J721S2 EVM which helps
users to enable MCU-MAIN MCSPI loopback applications, even though
the overlay is named j7200-mcspi-loopback.dtbo, same can be used
for testing on other J7 platforms as well.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the MCSPI loopback overlay file for J721E EVM which helps
users to enable MCU-MAIN MCSPI loopback applications, even though
the overlay is named j7200-mcspi-loopback.dtbo, same can be used
for testing on other J7 platforms as well.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J784S4 SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J721S2 SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J721E SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add device tree overlay for extending support for mcu_uart0 as well as
wkup_uart0 for boards with J7200 SoC. This overlay will mainly be used
for the purpose of testing uart instances.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The SHA for optee_os had been of 3.20-rc1 tag instead of 3.20 tag which
had been marked stable. Change the tag to 3.20.
Fixes: 280e7b4b3a ("optee: update optee components to 3.20 tag")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The AM69 SK has PWM output pins connected to its RPi header. Add
overlay file to enable PWM pins.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the basic J784S4 HS-FS configuration.
* Add configurations to support both HS-FS and GP keeping GP as default.
* Add ti-sci-firmware overrides for HS-FS.
* Remove evm conf file inclusion in hs-evm conf.
* Add j784s4 hs-evm specific config to hs-evm conf.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62A configuration
- Add machine conf for AM62A.
- The wic images will boot on AM62A HS-FS devices by default. The sysfw image for GP and HS-SE will be packaged in the wic image as tiboot3-am62ax-gp-evm.bin and tiboot3-am62ax-hs-evm.bin respectively.
- Add ti-sci-firmware overrides.
- Sign ATF, OPTEE and RTOS Firmware.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the basic J721S2 HS-FS configuration.
- Add configurations to support both HS-FS and GP keeping GP
as default.
- Add ti-sci-firmware overrides for HS-FS.
- Remove evm conf file inclusion in hs-evm conf.
- Add j721s2 hs-evm specific config to hs-evm conf.
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
With the advent of using multiconfigs to build all of the versions of
the machines (gp, hs-se, hs-fs, etc...) the sysfw.itb has become a point
of contention for do_deploy. To resolve the duplicate file copy errors
from bitbake we need to uniquify the sysfw.itb file names. So, let's do
the same thing we do with the tiboot3.bin file and add the SYSFW_SUFFIX
into the name.
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62x LP HS-FS configuration
- Add machine conf for AM62x LP HS-FS.
- The wic images will boot on AM62x LP HS-FS devices by default. The sysfw image for HS-SE will be packaged in the wic image as tiboot3-am62x-hs-evm.bin.
- Add ti-sci-firmware overrides.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62x HS-FS configuration
- Add machine conf for AM62x HS-FS.
- The wic images will boot on AM62x HS-FS devices by default. The sysfw image for GP and HS-SE will be packaged in the wic image as tiboot3-am62x-gp-evm.bin and tiboot3-am62x-hs-evm.bin respectively.
- Add ti-sci-firmware overrides.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
K3 platforms include the FIT image-based kernel by default. The bootloader
loads the kernel and DTB from the FIT image. The DTB/DTBOs are added to the
FIT image but the load address is not included in the image section of
each DTB/DTBO. This load address is determined by the LOADADDRESS macros
in the kernel-fitmage class.
Hence, define the RD/DTB/DTBOs LOADADDRESS and OFFSET macros in the K3 common
include, and remove those macros defined in the K3 board specific config files.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The AM68 SK has PWM output pins connected to its RPi headers. Add
overlay file to enable PWM pins.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Use ti-k3-secdev native package to provide secure-binary-image.sh script
when it is not passed on as an environment variable. This fixes and issue
with AM64xx which is always HS but should not require TI_SECURE_DEV_PKG
when building for HS-FS platforms.
This is backported from a patch for kirkstone. [1]
[1] https://lists.yoctoproject.org/g/meta-ti/topic/master_kirkstone_patch_1_8/96819771
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
OPTEE tests is not being upgraded due to a newer python dependency for
the build
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the overlay files for AM69 SK:
1. Fusion board (For FPDLink-III cameras).
2. IMX390 FPDLink-III camera module that includes both the CM and
RCM type of modules.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
This reverts commit 9a007a3fea.
We ran into some build failures on the older legacy platforms due
to this change and so are reverting this while we investigate.
OPTEE tests is not being upgraded due to a newer python dependency for
the build
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lets add the basic AM62x HS-SE configuration.
- Add machine conf for AM62x HS-SE.
- The wic images will boot on AM62x GP devices by default. To boot on AM62x HS-SE, simply switch out the SYSFW image:
$ cd /mnt/sd-card/boot
$ mv tiboot3-am62x-hs-evm.bin tiboot3.bin
- Add ti-sci-firmware overrides.
- Add support to sign ATF and OPTEE.
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the overlay files, over AM68 SK, for the following:
1. Fusion board (For FPDLink-III cameras).
2. IMX390 FPDLink-III camera module which includes both the CM and
RCM type of modules.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The extension for OV5640 overlay is incorrect. Therefore, update the
correct extension to build the overlay with .dtbo
Fixes: f67e9805 ("conf: machine: j721s2: Add AM68 SK specific dtb and dtbo to KERNEL_DEVICETREE")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
update the SHA of k3conf to pickup am62ax support
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
AM69 Starter Kit is a single board designed based on TI's AM69 SOC
providing advanced system integration in automotive ADAS applications,
autonomous mobile robot and edge AI applications. Add support
for the same to include the board dtb file into the root filesystem.
Add DT overlays support for the following features on AM69 SK:
* Add DTBO entry to support OV5640 camera
* Add DTBO entry to support RPi(IMX219) camera
* Add DTBO entry for the DDR memory carveout.
[1]:https://www.ti.com/lit/zip/spruj52
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Upgrade arm-trusted-firmare to v2.8-226-g2fcd408bb.
This upgrade picks up K3 L2 cache, snoop delayed, and EA
handling updates from upstream master.
Do not update to tip of master due to PSCI system off
support breaking AM62x and AM62q platforms.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Denys Dmytriyenko <denys@konsulko.com>
Tested-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
- Let's add support for secure RTOS IPC Firmware images for am62xx. This will sign RTOS IPC Firmware for all EVMs based on am62xx (i.e AM62X and AM62X-LP-EVM)
Signed-off-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
commit 98506a4a07 ("optee-os: Update SRCREV for OP-TEE TRNG in AM62X")
Disables SW PRNG => Enabling Hardware RNG. This is breaking Suspend Resume
on AM62xx EVM variants. To fix this keep using SOFTWARE_PRNG enabled as
it was.
Cc: vibhore@ti.com
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
In addition to releasing the signed versions of the bl31.bin and
bl32.bin files, also release the unsigned original versions.
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Bump source revision. Changelog from source:
- Cleanup the device initialization routine for all platforms
- Add a power safeguard for multicore initialization
- Enable active power management for AM62 devices
Signed-off-by: Randolph Sapp <rs@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
IMX390 is a 2MP FPDLink-III raw camera. This sensor was originally
targeted for J7-based devices, but AM62A can re-use the existing
overlays. Both the CM and RCM type of modules are supported.
As AM62A only has one CSI-RX port, we only use 4 out of the 8 total
FPDLink ports on the fusion board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
AM68 Starter Kit is a low cost, small form factor board designed for
TI's AM68/J721S2 SoC[1] which is optimized to provide best in class performance
for industrial applications. Add DTB entry for the same.
AM68 SK features camera support with MIPI(OV5640) and RPi(IMX219) connectors.
Add DTBO for the same. Also, add DTBO entry for the DDR memory carveout.
[1]:http://www.ti.com/lit/zip/spruj28
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Lower the log level for am62axx platform
commit 27641e1f2d ("optee-os: Lower log level for AM62x")
changes the log level for am62xx platforms.
This patch is to extend the same for am62axx
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reported-by: Sai Sree Kartheek Adivi <s-adivi@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Update library to 0.5.2 as it adds support for AM62A
SoC.
Co-Authored-By: Sai Sree Kartheek Adivi <s-adivi@ti.com>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the following overlay files on AM62A SK:
1. Fusion board (For FPDLink-III cameras)
2. OV2312 FPDLink camera module
3. IMX219 RPi-compatible camera module
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
optee-os was updated to 3.19 tag but the others were still outdated.
Updates other optee components to 3.19 tag
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
While removing SOFTWARE_PRNG support
commit:98506a4a07363a1b57012ccfaee263f47e5b46c4,
accidently removed the changes applied
by commit:27641e1f2d7f6696fd7bbd8f24fcac20766b6234
(optee-os: Lower log level for AM62x).
Reverting those changes back
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
With a recent patch to the TI kernel that includes debug symbols,
the vmlinux.gz file grew in size that impacted the testing.
This file is not needed to be in the final image so remove it
from the list.
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Update the SRCREV to the commit when trng support was
added in upstream OP-TEE for am62x platform to access rng.
Also, enable trng support as trng support is added now in OP-TEE
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the HS platform to the compatible list in the recipe.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the HS platform to the compatible list in the recipe.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Changes to support new j784s4-hs platform in:
1) ti-sci-fw_git: Update firmware prefix for j784s4-hs
2) atf: sign the image
4) optee: sign the image
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Sign the firmwares for j784s4 similar to j721s2 hs.
Duplicate all j784s4 entries for j784s4-hs as we cannot use same
keyword for match between j784s4-evm and j784s4-hs-evm.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Machine conf for J784S4 HS platform.
Used J721S2 hs as reference.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Otherwise undefined variable is returned literally as ${TI_SECURE_DEV_PKG_K3}
and the condition won't work.
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Denys Dmytriyenko <denys@konsulko.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Include ti-paths.inc so TI_K3_SECDEV_INSTALL_DIR_RECIPE gets defined and
artifacts are installed in the correct location.
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Denys Dmytriyenko <denys@konsulko.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Bump the source revision for the rogue pvr kernel module.
Source changelog:
- A hack was added to increase stability on J7 platforms while we are
looking into a proper fix for cache coherency issues in this module
Signed-off-by: Randolph Sapp <rs@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
update firmware name to wave521c_k3_codec_fw.bin to align with
linux-firmware main branch. the following patch is part of
ti-linux-firmware thru mainline sync.
commit 48407ffd ("cnm: update chips&media wave521c firmware.")
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
OP-TEE upstream now has support for sa3ul for j721s2 platform.
Re-enable the trng driver which was disabled earlier.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Change the OP-TEE flavour from default k3-j721e to k3-j784s4
as sa3ul support for j784s4 is upstreamed in OP-TEE and we
can use the same settings in j721s2 to access TRNG.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Add the new OP-TEE flavour for J784S4 instead of default k3-j721e.
The TI-SCI ID for MCU domain sa2ul/sa3ul are not the same for
J721E and J784S4. So a new flavour is added in upstream OP-TEE.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Update the SRCREV to the commit when sa3ul support was
added in upstream OP-TEE for J784S4 platform to access rng.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Serial console in J721S2/J784S4 EVM config was set to ttyS10. It should be ttyS2.
This caused sysv based systems (eg, tiny) to apparently hang because of no login prompt.
This didn't show up as a problem on systemd systems (eg, default) because systemd will
automatically setup a serial tty with the console option passed in on the kernel command line
(using console=...), which U-Boot correctly passes in as ttyS2 for J721S2/J784S4.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Bump the graphics recipes source revision and remove the old BVNC
switch. The BVNC is now baked into the platform Makefile that is
selected with PVR_BUILD_DIR / TARGET_PRODUCT.
Signed-off-by: Randolph Sapp <rs@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Update the ti-rpmsg-char library to 0.5.1 version that enables the
support for R5F on am62x SoCs.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Adds support for secure firmware images in J721S2 HS EVM.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Adds support for secure firmware images in J7200 HS EVM.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Adds support for secure firmware images in J721E HS EVM.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
devtool has a long-standing bug where it cannot handle references to ${WORKDIR}
due to externalsrc:
https://bugzilla.yoctoproject.org/show_bug.cgi?id=12677
linux-ti-mainline clones additional ti-upstream-tools repo alongside the kernel
sources into ${WORKDIR}, which exposes this devtool bug.
Work around the issue by moving ti-upstream-tools inside the kernel source tree,
i.e. inside ${S}
Reported-by: Radoslav Pesek <radoslav.pesek@microstep-mis.com>
Signed-off-by: Denys Dmytriyenko <denys@konsulko.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The supported device types depends on the SoC, not on any specific
board or EVM. Any board can be populated with any of the 3 supported
AM64x types. Move these into the AM64x common include.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
AM64x devices will only be available as SR2.0 HS-FS. Set this as the
default type provided by the SDK. To allow SR2.0 HS-SE to continue to
boot, like we did with GP, we add an extra machine to build SR2.0 HS-SE
SYSFW. To use on SR2.0 HS-SE boards simply switch out the SYSFW image:
$ cd /mnt/sd-card/boot
$ mv tiboot3-am64x_sr2-hs-evm.bin tiboot3.bin
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
cdns mhdp bridge is present in j721s2 soc.
Add the dependency for the same
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Switch the DEPENDS_append expression to use d.getVar() instead of the
usual variable expansion to prevent the inline Python command from
becoming mangled.
Signed-off-by: Randolph Sapp <rs@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
During resume from low power mode suspend OP-TEE prints some messages
on the UART. It seems this UART is not powered at this point in the
sequence breaking suspend/resume. We should track down the exact
prints and quiet them. Until we get that fix upstream, lets lower
the log level for this platform to unblock the LPM work.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Update to the latest upstream master which is 3.18.0.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The regex originally to correct all URLs that were still using the old
git protocol didn't have a check in place to see if the URL was already
using the correct protocol.
This just fixes the two affected URLs.
Signed-off-by: Randolph Sapp <rs@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
This platform is similar to the currently supported am62xx-evm, except
that we currently need new defconfigs for u-boot and new dtbs in the
filesystem.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Hari Nagalla <hnagalla@ti.com>
Cc: Andrew Davis <afd@ti.com>
Cc: Praneeth Bajjuri <praneeth@ti.com>
Cc: Ryan Eatmon <reatmon@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
In the latest U-Boot the HS images for AM64x have been renamed to the
default names, and the GP have been changed to *_unsigned. Remove
the overrides to pull the now default HS images.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
This is needed for building the latest optee-examples.
While here switch to HTTPS for fetching from Github.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
The HS-SE AM64xx machine can now be run on GP devices and built without
needing the TI_SECURE_DEV_PKG for the same. AM64xx will only be available
in the HS-FS type going forward. Make the HS-SE the default and remove
the original GP machine.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
