optee-os: restore libgcc-sysroot patch with newer version

The patch was dropped with 3.17 update:

https://git.yoctoproject.org/meta-ti/commit/?h=dunfell&id=f8182afdcfe427865707077d353359827f1ff6bf

But the patch is still needed for internal OE-built toolchain to pass
sysroot, otherwise libgcc.a cannot be found:

| aarch64-oe-linux-ld.bfd: cannot find libgcc.a: No such file or directory

The older version from meta-arm/dunfell no longer applies, so copy a newer
version of the patch locally.

Signed-off-by: Denys Dmytriyenko <denys@konsulko.com>
Signed-off-by: Ryan Eatmon <reatmon@ti.com>

.gitignore

@@ -1,6 +0,0 @@
-*.pyc
-*.pyo
-*.swp
-*.orig
-*.rej
-*~

README

@@ -1,4 +1,33 @@
-Collection of layers for the OE-core universe
+The official OpenEmbedded/Yocto BSP layer for Texas Instruments platforms.
 
-Please see the respective READMEs in the layer subdirectories
+It is hosted on http://git.yoctoproject.org/cgit/cgit.cgi/meta-ti/ with the
+source repository at git://git.yoctoproject.org/meta-ti
 
+
+This layer depends on:
+
+URI: git://git.openembedded.org/openembedded-core
+layers: meta
+branch: dunfell
+
+URI: git://git.yoctoproject.org/meta-arm
+layers: meta-arm
+branch: dunfell
+
+
+The base BSP part of meta-ti should work with different OpenEmbedded/Yocto
+distributions and layer stacks, such as:
+distro-less (only with OE-Core), with Yocto/Poky, with Angstrom or Arago.
+
+Please follow the recommended setup procedures of your OE distribution.
+
+
+Send pull requests, patches, comments or questions to:
+meta-ti@lists.yoctoproject.org
+
+Please note - meta-ti mailing list requires subscription for posting:
+https://lists.yoctoproject.org/g/meta-ti
+
+Maintainers:
+Ryan Eatmon <reatmon@ti.com>
+Denys Dmytriyenko <denys@konsulko.com>

classes/ti-pdk-fetch.bbclass

@@ -0,0 +1,47 @@
+TI_PDK_GIT_URI ?= "git://git.ti.com/git/processor-sdk/pdk.git"
+TI_PDK_GIT_BRANCH ?= "master"
+TI_PDK_GIT_PROTOCOL ?= "https"
+TI_PDK_SRCREV ?= "a1ace885998e9adbcbbd0abf8b9ded6ba9ec54ff"
+
+TI_PDK_VERSION ?= "2020.5.6"
+
+PV = "${TI_PDK_VERSION}"
+PE = "2"
+
+TI_PDK_COMP ?= ""
+TI_PDK_COMP_PATH = "${@'${TI_PDK_COMP}'.replace('.','/')}"
+
+TI_PDK_SOURCE_PN = "ti-pdk-source"
+TI_PDK_SOURCE_WORKDIR = "${TMPDIR}/work-shared/ti-pdk-${PV}"
+TI_PDK_SOURCE = "${TI_PDK_SOURCE_WORKDIR}/git"
+
+S = "${@'${WORKDIR}/git/${TI_PDK_COMP_PATH}'.rstrip('/')}"
+
+# Hard-link only required sources from PDK
+python do_unpack_append() {
+    if len(d.getVar('TI_PDK_COMP') or '') > 0:
+        import shutil
+
+        # Get src/dst paths
+        src = os.path.join(d.getVar('TI_PDK_SOURCE'),'packages',d.getVar('TI_PDK_COMP_PATH'))
+        s = d.getVar('S')
+
+        # Set up the directory structure, except for the root of the sources
+        # hard-linked.
+        bb.utils.mkdirhier(s)
+        os.rmdir(s)
+
+        # Recursively hard-link the sources
+        shutil.copytree(src, s, copy_function=os.link)
+
+        # Recursively hard-link the git directory
+        shutil.copytree(os.path.join(d.getVar('TI_PDK_SOURCE'),'.git'), os.path.join(s,'.git'), copy_function=os.link)
+}
+
+# Make sure that ti-pdk-source is unpacked before we set up the hardlinks.
+python __anonymous () {
+    pn = d.getVar('PN')
+    pdk_src_pn = d.getVar('TI_PDK_SOURCE_PN')
+    if pn != pdk_src_pn:
+        d.appendVarFlag('do_unpack', 'depends', ' ${TI_PDK_SOURCE_PN}:do_unpack')
+}

classes/ti-pdk.bbclass

@@ -0,0 +1,144 @@
+require recipes-ti/includes/ti-paths.inc
+require recipes-ti/includes/ti-staging.inc
+
+inherit perlnative
+
+DEPENDS = "ti-xdctools-native ti-cg-xml-native ti-sysbios common-csl-ip-rtos libxml-simple-perl-native gcc-arm-baremetal-native ti-cgt6x-native ti-cgt-pru-native ti-pdk-build-rtos doxygen-native"
+
+DEPENDS_append_omap-a15 = " ti-cgt-arm-native"
+DEPENDS_remove_ti33x = "ti-cgt6x-native"
+DEPENDS_remove_ti43x = "ti-cgt6x-native"
+DEPENDS_append_omapl1 = " ti-cgt-arm-native"
+DEPENDS_remove_am65xx = "gcc-arm-baremetal-native ti-cgt6x-native"
+DEPENDS_append_am65xx = " ti-cgt-arm-native gcc-linaro-baremetal-aarch64-native"
+DEPENDS_remove_j7 = "gcc-arm-baremetal-native"
+DEPENDS_append_j7 = " ti-cgt-arm-native gcc-linaro-baremetal-aarch64-native ti-cgt7x-native"
+
+S = "${WORKDIR}/git"
+B = "${WORKDIR}/build"
+
+# HTML hyperlink text
+PDK_COMP_LINK_TEXT ?= ""
+
+DOC_FILE = "API_Documentation_${PN}.html"
+
+create_doc_link () {
+    PDK_COMP_DIR=`get_build_dir_bash`
+
+    echo "<a href=\"${PDK_COMP_DIR}/docs/doxygen/html/index.html\">${PDK_COMP_LINK_TEXT}</a>" >> ${D}${PDK_INSTALL_DIR_RECIPE}/packages/.extras/doc/${DOC_FILE}
+}
+
+get_build_dir_bash() {
+  if [ -f ${S}/package.xdc ]
+  then
+    grep '^package' ${S}/package.xdc | sed -e 's|\[.*$||' | awk '{ print $2 }' | sed -e 's|\.|/|g'
+  else
+    echo ${S}
+    return 1
+  fi
+}
+
+export CROSS_TOOL_PRFX="arm-none-eabi-"
+export TOOLCHAIN_PATH_A8 = "${GCC_ARM_NONE_TOOLCHAIN}"
+export TOOLCHAIN_PATH_A9 = "${GCC_ARM_NONE_TOOLCHAIN}"
+export TOOLCHAIN_PATH_A15 = "${GCC_ARM_NONE_TOOLCHAIN}"
+export TOOLCHAIN_PATH_M4 = "${M4_TOOLCHAIN_INSTALL_DIR}"
+export TOOLCHAIN_PATH_Arm9 = "${M4_TOOLCHAIN_INSTALL_DIR}"
+export C6X_GEN_INSTALL_PATH = "${STAGING_DIR_NATIVE}/usr/share/ti/cgt-c6x"
+export C7X_GEN_INSTALL_PATH = "${STAGING_DIR_NATIVE}/usr/share/ti/cgt-c7x"
+export TOOLCHAIN_PATH_EVE = "${STAGING_DIR_NATIVE}/usr/share/ti/cgt-arp32"
+export CL_PRU_INSTALL_PATH = "${TI_CGT_PRU_INSTALL_DIR}"
+export TOOLCHAIN_PATH_GCC_ARCH64 = "${GCC_LINARO_BAREMETAL_AARCH64_TOOLCHAIN}"
+export TOOLCHAIN_PATH_R5 = "${M4_TOOLCHAIN_INSTALL_DIR}"
+
+export ROOTDIR = "${B}"
+export BIOS_INSTALL_PATH = "${SYSBIOS_INSTALL_DIR}"
+export XDC_INSTALL_PATH = "${XDC_INSTALL_DIR}"
+export PDK_INSTALL_PATH = "${PDK_INSTALL_DIR}/packages"
+
+export XDCPATH = "${XDC_INSTALL_DIR}/packages;${SYSBIOS_INSTALL_DIR}/packages;${PDK_INSTALL_DIR}/packages"
+export SECTTI="perl ${CG_XML_INSTALL_DIR}/ofd/sectti.pl"
+
+TI_PDK_XDCMAKE ?= "1"
+
+# By default, only build the cores with available toolchains
+TI_PDK_LIMIT_CORES ?= "a15_0 ipu1_0 ipu1_1 ipu2_0 ipu2_1 mpu1_0 mcu1_0 mcu1_1 mcu2_0 mcu2_1 mcu3_0 mcu3_1 c66x c66xdsp_1 c66xdsp_2 c7x_1 arm9_0 c674x a9host a8host pru_0 pru_1"
+TI_PDK_LIMIT_SOCS ?= ""
+TI_PDK_LIMIT_BOARDS ?= ""
+TI_PDK_MAKE_TARGET ?= "release"
+TI_PDK_EXTRA_MAKE ?= ""
+TI_PDK_DOXYGEN_SUPPORT ?= "1"
+
+TI_PDK_XDC_ARGS ?= "${TI_PDK_LIMIT_SOCS}"
+
+PARALLEL_XDC = "${@oe.utils.parallel_make_argument(d, '--jobs=%d')}"
+PARALLEL_MAKE = ""
+
+def get_doxygen_support(d):
+    if d.getVar('TI_PDK_DOXYGEN_SUPPORT') == '1':
+        return ''
+    return 'DOXYGEN_SUPPORT=no'
+
+EXTRA_OEMAKE = " \
+    LIMIT_SOCS="${TI_PDK_LIMIT_SOCS}" \
+    LIMIT_BOARDS="${TI_PDK_LIMIT_BOARDS}" \
+    LIMIT_CORES="${TI_PDK_LIMIT_CORES}" \
+    ${TI_PDK_EXTRA_MAKE} \
+    ${@get_doxygen_support(d)} \
+"
+
+do_configure() {
+    BUILD_DIR=${B}/`get_build_dir_bash`
+
+    mkdir -p ${BUILD_DIR}
+    cp -r ${S}/* ${BUILD_DIR}
+
+    if [ "${TI_PDK_XDCMAKE}" == "1" ]
+    then
+        cd ${BUILD_DIR}
+
+        sed -i "s/\ \"\.\\\\\\\\\"\ +//" src/Module.xs
+        find -name "*.xs" -exec sed -i "s/ofd6x\.exe/ofd6x/" {} \;
+        find -name "*.xs" -exec sed -i "s/sectti\.exe/sectti/" {} \;
+        find -name "*.xs" -exec sed -i "/\.chm/d" {} \;
+        find -name "*.xs" -exec sed -i "s/pasm\_dos/pasm\_linux/" {} \;
+
+        cd ${B}
+        ${XDC_INSTALL_DIR}/xdc clean ${PARALLEL_XDC} -PR .
+    else
+        if [ "${CLEANBROKEN}" != "1" ]
+        then
+            cd ${BUILD_DIR}
+            oe_runmake clean
+            cd "${B}"
+        fi
+    fi
+
+}
+
+do_compile() {
+
+    if [ "${TI_PDK_XDCMAKE}" == "1" ]
+    then
+        ${XDC_INSTALL_DIR}/xdc all ${PARALLEL_XDC} XDCARGS="${TI_PDK_XDC_ARGS}" ROOTDIR="${ROOTDIR}" -PR .
+        ${XDC_INSTALL_DIR}/xdc release XDCARGS="${TI_PDK_XDC_ARGS}" -PR .
+    else
+        BUILD_DIR=${B}/`get_build_dir_bash`
+        cd ${BUILD_DIR}
+
+        oe_runmake ${TI_PDK_MAKE_TARGET}
+    fi
+}
+
+do_install () {
+    install -d ${D}${PDK_INSTALL_DIR_RECIPE}/packages
+    find -name "*.tar" -exec tar xf {} --no-same-owner -C ${D}${PDK_INSTALL_DIR_RECIPE}/packages \;
+    
+    if [ "${PDK_COMP_LINK_TEXT}" != "" ]
+    then
+        install -d ${D}${PDK_INSTALL_DIR_RECIPE}/packages/.extras/doc
+        create_doc_link
+    fi
+}
+
+FILES_${PN} += "${PDK_INSTALL_DIR_RECIPE}/packages"

conf/layer.conf

@@ -0,0 +1,35 @@
+# We have a conf and classes directory, append to BBPATH
+BBPATH .= ":${LAYERDIR}"
+METATIBASE := '${@os.path.normpath("${LAYERDIR}/")}'
+
+# We have a recipes directory, add to BBFILES
+BBFILES += "${LAYERDIR}/recipes*/*/*.bb ${LAYERDIR}/recipes*/*/*.bbappend"
+
+BBFILE_COLLECTIONS += "meta-ti"
+BBFILE_PATTERN_meta-ti := "^${LAYERDIR}/"
+BBFILE_PRIORITY_meta-ti = "6"
+
+LAYERSERIES_COMPAT_meta-ti = "dunfell"
+
+LICENSE_PATH += "${LAYERDIR}/licenses"
+
+LAYERDEPENDS_meta-ti = " \
+    core \
+    meta-arm \
+"
+
+SIGGEN_EXCLUDERECIPES_ABISAFE += " \
+    ti-sgx-ddk-km \
+    ti-sgx-ddk-um \
+    cmem-mod \
+    hplib-mod \
+    gdbserverproxy-module-drv \
+    debugss-module-drv \
+    uio-module-drv \
+    mpm-transport \
+    cppi-lld \
+    qmss-lld \
+    multiprocmgr \
+"
+
+HOSTTOOLS_NONFATAL += "truncate xxd comm"

conf/machine/am335x-evm.conf

@@ -4,12 +4,14 @@
 
 require conf/machine/include/ti33x.inc
 
-MACHINE_FEATURES += "screen touchscreen"
+MACHINE_GUI_CLASS = "smallscreen"
+MACHINE_FEATURES += "touchscreen"
 
 IMAGE_FSTYPES += "ubifs ubi"
 
 # Normally AM335 boards use ttyS0, but ICE uses ttyS3, so try both
 SERIAL_CONSOLES = "115200;ttyS0 115200;ttyS3"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
 
 # UBI information.  Note that this is board and kernel specific.  Changes
 # in your kernel port may require changes in these variables.  For more
@@ -22,7 +24,7 @@ SERIAL_CONSOLES = "115200;ttyS0 115200;ttyS3"
 # UBI: logical eraseblock size:    126976 bytes
 # from ubiattach stdout:
 # UBI device number 0, total 1988 LEBs
-MKUBIFS_ARGS ?= "-F -m 2048 -e 126976 -c 13000"
+MKUBIFS_ARGS ?= "-F -m 2048 -e 126976 -c 9900"
 
 # do ubiattach /dev/ubi_ctrl -m 7 -O 2048
 # from dmesg:

conf/machine/am335x-hs-evm.conf

@@ -15,12 +15,4 @@ UBOOT_LOADADDRESS = "0x82000000"
 UBOOT_RD_LOADADDRESS = "0x84000000"
 UBOOT_RD_ENTRYPOINT = "0x84000000"
 
-# FIT image for legacy secure devices
-KERNEL_CLASSES += " kernel-fitimage-legacyhs"
-KERNEL_IMAGETYPES += " fitImage"
-
-# FIT image settings
-FITIMAGE_HASH_ALGO = ""
-FITIMAGE_DTB_BY_NAME = "1"
-FITIMAGE_TEE_BY_NAME = "1"
-FITIMAGE_CONF_BY_NAME = "1"
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_CAT}/am3x"

conf/machine/am3517-evm.conf

@@ -0,0 +1,35 @@
+#@TYPE: Machine
+#@NAME: AM3517 EVM
+#@DESCRIPTION: Machine configuration for the TI Sitara AM3517 EVM
+
+require conf/machine/include/omap3.inc
+
+MACHINE_GUI_CLASS = "smallscreen"
+MACHINE_FEATURES += "touchscreen ethernet"
+
+IMAGE_FSTYPES += "ubi tar.xz"
+EXTRA_IMAGECMD_jffs2 = "-lnp -e 0x20000 -s 2048"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+USE_VT = "2"
+
+KERNEL_DEVICETREE = "am3517-evm.dtb"
+
+UBOOT_MACHINE = "am3517_evm_config"
+XLOAD_MACHINE = "am3517evm_config"
+
+# NOTE: there are NAND and OneNAND versions of this board...
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    129024 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1996 LEBs
+MKUBIFS_ARGS = "-m 2048 -e 129024 -c 1996"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              512
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512"

conf/machine/am37x-evm.conf

@@ -0,0 +1,31 @@
+#@TYPE: Machine
+#@NAME: AM37x EVM
+#@DESCRIPTION: Machine configuration for the TI AM37x EVM
+
+require conf/machine/include/omap3.inc
+
+MACHINE_GUI_CLASS = "smallscreen"
+MACHINE_FEATURES += "touchscreen ethernet"
+
+IMAGE_FSTYPES += "ubi tar.xz"
+EXTRA_IMAGECMD_jffs2 = "-lnp -e 0x20000 -s 2048"
+
+KERNEL_DEVICETREE = "omap3-evm-37xx.dtb"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+
+# NOTE: there are NAND and OneNAND versions of this board...
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    129024 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1996 LEBs
+MKUBIFS_ARGS = "-m 2048 -e 129024 -c 1996"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              512
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512"

conf/machine/am437x-evm.conf

@@ -4,6 +4,7 @@
 
 require conf/machine/include/ti43x.inc
 
+MACHINE_GUI_CLASS = "smallscreen"
 MACHINE_FEATURES += "touchscreen"
 
 IMAGE_FSTYPES += "ubifs ubi"
@@ -21,7 +22,7 @@ SERIAL_CONSOLES = "115200;ttyS0"
 # UBI: logical eraseblock size:    253952 bytes
 # from ubiattach stdout:
 # UBI device number 0, total 994 LEBs
-MKUBIFS_ARGS = "-F -m 4096 -e 253952 -c 8000"
+MKUBIFS_ARGS = "-F -m 4096 -e 253952 -c 4800"
 
 # do ubiattach /dev/ubi_ctrl -m 11 -O 4096
 # from dmesg:

conf/machine/am437x-hs-evm.conf

@@ -11,18 +11,8 @@ UBOOT_LOADADDRESS = "0x82000000"
 UBOOT_RD_LOADADDRESS = "0x84000000"
 UBOOT_RD_ENTRYPOINT = "0x84000000"
 
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_CAT}/am4x"
+
 OPTEEMACHINE = "ti-am43xx"
 OPTEEFLAVOR = "am43xx"
-
-EXTRA_IMAGEDEPENDS += "optee-os"
-
-# FIT image for legacy secure devices
-KERNEL_CLASSES += " kernel-fitimage-legacyhs"
-KERNEL_IMAGETYPES += " fitImage"
-
-# FIT image settings
-FITIMAGE_HASH_ALGO = ""
-FITIMAGE_PACK_TEE = "1"
-FITIMAGE_DTB_BY_NAME = "1"
-FITIMAGE_TEE_BY_NAME = "1"
-FITIMAGE_CONF_BY_NAME = "1"
+OPTEEOUTPUTMACHINE = "ti"

conf/machine/am57xx-evm.conf

@@ -0,0 +1,58 @@
+#@TYPE: Machine
+#@NAME: AM57xx EVM
+#@DESCRIPTION: Machine configuration for the TI AM57xx EVM
+
+require conf/machine/include/dra7xx.inc
+
+MACHINE_FEATURES += "touchscreen"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+
+KERNEL_DEVICETREE = " \
+    am57xx-beagle-x15.dtb \
+    am57xx-beagle-x15-revb1.dtb \
+    am57xx-beagle-x15-revc.dtb \
+    am5729-beagleboneai.dtb \
+    ${@oe.utils.conditional('ARAGO_BRAND', 'mainline', '', 'am57xx-evm.dtb', d)} \
+    ti/am57xx-evm-common.dtbo \
+    ${@oe.utils.conditional('ARAGO_BRAND', 'mainline', '', 'am57xx-evm-reva3.dtb', d)} \
+    ti/am57xx-evm-reva3.dtbo \
+    am571x-idk.dtb \
+    ti/am571x-idk-touchscreen.dtbo \
+    am572x-idk.dtb \
+    am574x-idk.dtb \
+    ti/am57xx-idk-osd-lcd-common.dtbo \
+    ti/am572x-idk-touchscreen.dtbo \
+    ti/lcd-osd101t2587.dtbo \
+    ti/lcd-osd101t2045.dtbo \
+    ${@oe.utils.conditional('ARAGO_BRAND', 'mainline', '', 'ti/ov10635.dtbo', d)} \
+"
+
+KERNEL_DEVICETREE += "${@oe.utils.conditional('ENABLE_TI_UIO_DEVICES', '1', 'am574x-idk-pru-excl-uio.dtb am572x-idk-pru-excl-uio.dtb am571x-idk-pru-excl-uio.dtb', '', d)}"
+
+UBOOT_MACHINE = "am57xx_evm_config"
+
+# UBI information.  Note that this is board and kernel specific.  Changes
+# in your kernel port may require changes in these variables.  For more
+# details about this board please see
+# http://processors.wiki.ti.com/index.php/UBIFS_Support
+
+# do ubiattach /dev/ubi_ctrl -m 7 -O 2048
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    126976 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1988 LEBs
+MKUBIFS_ARGS = "-F -m 2048 -e 126976 -c 8192"
+
+# do ubiattach /dev/ubi_ctrl -m 7 -O 2048
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              512
+# UBI: VID header offset:          2048 (aligned 2048)
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512 -O 2048"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "am571x am572x am574x"
+TI_PDK_LIMIT_BOARDS = "evmAM571x evmAM572x idkAM571x idkAM572x idkAM574x"

conf/machine/am57xx-hs-evm.conf

@@ -11,19 +11,9 @@ UBOOT_LOADADDRESS = "0x82000000"
 UBOOT_RD_LOADADDRESS = "0x84000000"
 UBOOT_RD_ENTRYPOINT = "0x84000000"
 
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_AUTO}/am5x"
+
 OPTEEMACHINE = "ti-am57xx"
 OPTEEFLAVOR = "am57xx"
+OPTEEOUTPUTMACHINE = "ti"
 OPTEEPAGER = "y"
-
-EXTRA_IMAGEDEPENDS += "optee-os"
-
-# FIT image for legacy secure devices
-KERNEL_CLASSES += " kernel-fitimage-legacyhs"
-KERNEL_IMAGETYPES += " fitImage"
-
-# FIT image settings
-FITIMAGE_HASH_ALGO = ""
-FITIMAGE_PACK_TEE = "1"
-FITIMAGE_DTB_BY_NAME = "1"
-FITIMAGE_TEE_BY_NAME = "1"
-FITIMAGE_CONF_BY_NAME = "1"

conf/machine/am62axx-evm-k3r5-gp.conf

@@ -0,0 +1,19 @@
+#@TYPE: Machine
+#@NAME: AM62A GP EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62A GP EVM (R5F core)
+
+require conf/machine/include/k3r5.inc
+
+SYSFW_SOC = "am62ax"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "gp"
+
+SYSFW_TIBOOT3_SYMLINK = ""
+SYSFW_SYMLINK = ""
+
+UBOOT_MACHINE = "am62ax_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-gp-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-gp.${UBOOT_SUFFIX}"

conf/machine/am62axx-evm-k3r5-hs-fs.conf

@@ -1,8 +1,11 @@
 #@TYPE: Machine
 #@NAME: AM62A HS-FS EVM (R5F)
-#@DESCRIPTION: Machine configuration for the TI AM62A EVM (R5F core)
+#@DESCRIPTION: Machine configuration for the TI AM62A HS-FS EVM (R5F core)
+
+# Booting HS-FS requires different SYSFW, the rest is handled at runtime
 
 require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-hs-fs"
 
 SYSFW_SOC = "am62ax"
 SYSFW_CONFIG = "evm"

conf/machine/am62axx-evm-k3r5-hs-se.conf

@@ -0,0 +1,22 @@
+#@TYPE: Machine
+#@NAME: AM62A HS-SE EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62A HS-SE EVM (R5F core)
+
+# Booting HS-SE requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-hs-se"
+
+SYSFW_SOC = "am62ax"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs"
+
+SYSFW_TIBOOT3_SYMLINK = ""
+SYSFW_SYMLINK = ""
+
+UBOOT_MACHINE = "am62ax_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-hs-se-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-hs-se.${UBOOT_SUFFIX}"

conf/machine/am62axx-evm.conf

@@ -0,0 +1,30 @@
+#@TYPE: Machine
+#@NAME: AM62AXX EVM
+#@DESCRIPTION: Machine configuration for the TI AM62AXX EVM
+
+require conf/machine/include/am62axx.inc
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am62a7-sk.dtb \
+    ti/k3-am62a7-fpdlink-ov2312-0-0.dtbo \
+    ti/k3-am62a7-fpdlink-ov2312-0-1.dtbo \
+    ti/k3-am62a7-fpdlink-ov2312-0-2.dtbo \
+    ti/k3-am62a7-fpdlink-ov2312-0-3.dtbo \
+    ti/k3-am62a7-fpdlink-sk-fusion.dtbo \
+    ti/k3-am62a7-sk-csi2-imx219.dtbo \
+    ti/k3-am62a7-sk-ethernet-dc01.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-3.dtbo \
+"
+
+UBOOT_MACHINE = "am62ax_evm_a53_defconfig"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"

conf/machine/am62xx-evm-k3r5-gp.conf

@@ -3,10 +3,16 @@
 #@DESCRIPTION: Machine configuration for the TI AM62xx EVM (R5F core)
 
 require conf/machine/include/k3r5.inc
-require conf/machine/include/ti-extras.inc
 
 SYSFW_SOC = "am62x"
 SYSFW_CONFIG = "evm"
-SYSFW_SUFFIX = "hs-fs"
+SYSFW_SUFFIX = "gp"
+
+SYSFW_TIBOOT3_SYMLINK = ""
 
 UBOOT_MACHINE = "am62x_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-gp-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-gp.${UBOOT_SUFFIX}"

conf/machine/am62xx-evm-k3r5-hs-fs.conf

@@ -0,0 +1,14 @@
+#@TYPE: Machine
+#@NAME: AM62xx HS-FS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62xx HS-FS EVM (R5F core)
+
+# Booting HS-FS requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-hs-fs"
+
+SYSFW_SOC = "am62x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs-fs"
+
+UBOOT_MACHINE = "am62x_evm_r5_defconfig"

conf/machine/am62xx-evm-k3r5-hs-se.conf

@@ -0,0 +1,21 @@
+#@TYPE: Machine
+#@NAME: AM62xx HS-SE EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62xx HS-SE EVM (R5F core)
+
+# Booting HS-SE requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-hs-se"
+
+SYSFW_SOC = "am62x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs"
+
+SYSFW_TIBOOT3_SYMLINK = ""
+
+UBOOT_MACHINE = "am62x_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-hs-se-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-hs-se.${UBOOT_SUFFIX}"

conf/machine/am62xx-evm.conf

@@ -0,0 +1,25 @@
+#@TYPE: Machine
+#@NAME: AM62XX EVM
+#@DESCRIPTION: Machine configuration for the TI AM62XX EVM
+
+require conf/machine/include/am62xx.inc
+
+MACHINE_FEATURES += "gpu"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am625-sk.dtb \
+    ti/k3-am625-skeleton.dtb \
+    ti/k3-am625-sk-lpmdemo.dtb \
+    ti/k3-am625-sk-csi2-ov5640.dtbo \
+    ti/k3-am625-sk-csi2-tevi-ov5640.dtbo \
+    ti/k3-am625-sk-ecap-capture.dtbo \
+    ti/k3-am625-sk-hdmi-audio.dtbo \
+    ti/k3-am625-sk-mcan.dtbo \
+    ti/k3-am625-sk-oldi-panel.dtbo \
+"
+
+UBOOT_MACHINE = "am62x_evm_a53_defconfig"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"

conf/machine/am62xx-lp-evm-k3r5-hs-fs.conf

@@ -0,0 +1,14 @@
+#@TYPE: Machine
+#@NAME: AM62xx LPSK HS-FS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62xx LP HS-FS EVM (R5F core)
+
+# Booting HS-FS requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-hs-fs"
+
+SYSFW_SOC = "am62x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs-fs"
+
+UBOOT_MACHINE = "am62x_lpsk_r5_defconfig"

conf/machine/am62xx-lp-evm-k3r5-hs-se.conf

@@ -0,0 +1,21 @@
+#@TYPE: Machine
+#@NAME: AM62xx LPSK HS-SE EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62xx LP HS-SE EVM (R5F core)
+
+# Booting HS-SE requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-hs-se"
+
+SYSFW_SOC = "am62x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs"
+
+SYSFW_TIBOOT3_SYMLINK = ""
+
+UBOOT_MACHINE = "am62x_lpsk_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-hs-se-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-hs-se.${UBOOT_SUFFIX}"

conf/machine/am62xx-lp-evm-k3r5.conf

@@ -0,0 +1,19 @@
+#@TYPE: Machine
+#@NAME: AM62XX LP GP EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM62xx LP GP EVM (R5F core)
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-gp"
+
+SYSFW_SOC = "am62x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "gp"
+
+SYSFW_TIBOOT3_SYMLINK = ""
+
+UBOOT_MACHINE = "am62x_lpsk_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-gp-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-gp.${UBOOT_SUFFIX}"

conf/machine/am62xx-lp-evm.conf

@@ -0,0 +1,21 @@
+#@TYPE: Machine
+#@NAME: AM62XX LP EVM
+#@DESCRIPTION: Machine configuration for the TI AM62XX LP EVM
+
+require conf/machine/include/am62xx-lp.inc
+
+MACHINE_FEATURES += "gpu"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am62x-lp-sk.dtb \
+    ti/k3-am625-skeleton.dtb \
+    ti/k3-am625-sk-lpmdemo.dtb \
+    ti/k3-am625-sk-csi2-ov5640.dtbo \
+    ti/k3-am62x-lp-sk-oldi-panel.dtbo \
+"
+
+SPL_BINARY = "tispl.bin_HS"	
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"
+
+UBOOT_MACHINE = "am62x_lpsk_a53_defconfig"

conf/machine/am64xx-evm-k3r5-gp.conf

@@ -0,0 +1,20 @@
+#@TYPE: Machine
+#@NAME: AM64xx GP EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM64xx GP EVM (R5F core)
+
+# Booting GP requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-gp"
+
+SYSFW_SOC = "am64x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "gp"
+SYSFW_TIBOOT3_SYMLINK = ""
+
+UBOOT_MACHINE = "am64x_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-gp-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-gp.${UBOOT_SUFFIX}"

conf/machine/am64xx-evm-k3r5-sr2-hs-fs.conf

@@ -0,0 +1,14 @@
+#@TYPE: Machine
+#@NAME: AM64xx SR2.0 HS-FS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM64xx SR2.0 HS-FS EVM (R5F core)
+
+# Booting SR2.0 HS-FS requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-sr2-hs-fs"
+
+SYSFW_SOC = "am64x_sr2"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs-fs"
+
+UBOOT_MACHINE = "am64x_evm_r5_defconfig"

conf/machine/am64xx-evm-k3r5-sr2-hs-se.conf

@@ -0,0 +1,20 @@
+#@TYPE: Machine
+#@NAME: AM64xx SR2.0 HS-SE EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM64xx SR2.0 HS-SE EVM (R5F core)
+
+# Booting SR2.0 HS-SE requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-sr2-hs-se"
+
+SYSFW_SOC = "am64x_sr2"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs"
+SYSFW_TIBOOT3_SYMLINK = ""
+
+UBOOT_MACHINE = "am64x_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-sr2-hs-se-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-sr2-hs-se.${UBOOT_SUFFIX}"

conf/machine/am65xx-evm-k3r5-sr2.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: AM65xx SR2.0 EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM65xx SR2.0 EVM (R5F core)
+
+# Booting SR2 requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/am65xx-evm-k3r5.conf
+SOC_FAMILY_append = ":k3r5-sr2"
+
+SYSFW_SOC = "am65x_sr2"
+SYSFW_SYMLINK = "sysfw.itb"

conf/machine/am65xx-evm-k3r5.conf

@@ -0,0 +1,18 @@
+#@TYPE: Machine
+#@NAME: AM65xx EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM65xx EVM (R5F core)
+
+require conf/machine/include/k3r5.inc
+
+SYSFW_SOC = "am65x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "gp"
+SYSFW_SYMLINK = ""
+
+SPL_BINARY = "spl/u-boot-spl.${UBOOT_SUFFIX}"
+SPL_SYMLINK = "u-boot-r5spl.${UBOOT_SUFFIX}"
+UBOOT_BINARY = "tiboot3.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "tiboot3-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "tiboot3-${MAINMACHINE}.${UBOOT_SUFFIX}"
+
+UBOOT_MACHINE = "am65x_evm_r5_defconfig"

conf/machine/am65xx-evm.conf

@@ -5,5 +5,3 @@
 require conf/machine/include/am65xx.inc
 
 UBOOT_MACHINE = "am65x_evm_a53_defconfig"
-
-MACHINE_ESSENTIAL_EXTRA_RRECOMMENDS += "prueth-fw pruhsr-fw prusw-fw"

conf/machine/am65xx-hs-evm-k3r5-sr2.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: AM65xx SR2.0 HS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM65xx SR2.0 HS EVM (R5F core)
+
+# Booting SR2 requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/am65xx-hs-evm-k3r5.conf
+SOC_FAMILY_append = ":k3r5-sr2"
+
+SYSFW_SOC = "am65x_sr2"
+SYSFW_SYMLINK = "sysfw.itb"

conf/machine/am65xx-hs-evm-k3r5.conf

@@ -0,0 +1,18 @@
+#@TYPE: Machine
+#@NAME: AM65xx HS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI AM65xx HS EVM (R5F core)
+
+require conf/machine/include/k3r5.inc
+
+SYSFW_SOC = "am65x"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs"
+SYSFW_SYMLINK = ""
+
+SPL_BINARY = "spl/u-boot-spl.${UBOOT_SUFFIX}"
+SPL_SYMLINK = "u-boot-r5spl.${UBOOT_SUFFIX}"
+UBOOT_BINARY = "tiboot3.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "tiboot3-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "tiboot3-${MAINMACHINE}.${UBOOT_SUFFIX}"
+
+UBOOT_MACHINE = "am65x_hs_evm_r5_defconfig"

conf/machine/am65xx-hs-evm.conf

@@ -4,4 +4,8 @@
 
 require conf/machine/include/am65xx.inc
 
-UBOOT_MACHINE = "am65x_evm_a53_defconfig"
+UBOOT_MACHINE = "am65x_hs_evm_a53_defconfig"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"

conf/machine/beagle-x15.conf

@@ -0,0 +1,13 @@
+#@TYPE: Machine
+#@NAME: BeagleBoard X15
+#@DESCRIPTION: Machine configuration for the BeagleBoard X15
+
+require conf/machine/include/dra7xx.inc
+
+KERNEL_DEVICETREE = "am57xx-beagle-x15.dtb am57xx-beagle-x15-revb1.dtb am57xx-beagle-x15-revc.dtb"
+
+MACHINE_GUI_CLASS = "bigscreen"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+
+UBOOT_MACHINE = "am57xx_evm_config"

conf/machine/beagleboard.conf

@@ -0,0 +1,38 @@
+#@TYPE: Machine
+#@NAME: Beagleboard machine
+#@DESCRIPTION: Machine configuration for the http://beagleboard.org/ board 
+
+require conf/machine/include/omap3.inc
+
+# Only has DVI connector for external screen
+MACHINE_GUI_CLASS = "bigscreen"
+
+IMAGE_FSTYPES += "tar.xz ubi"
+EXTRA_IMAGECMD_jffs2 = "-lnp"
+
+KERNEL_DEVICETREE = "omap3-beagle.dtb omap3-beagle-xm.dtb omap3-beagle-xm-ab.dtb"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+
+UBOOT_MACHINE = "omap3_beagle_config"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    129024 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1996 LEBs
+# 
+# Beagleboard C5 has 3998 LEBS (490MiB)
+MKUBIFS_ARGS = "-m 2048 -e 129024 -c 1996"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              512
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512"
+
+# For a modularized kernel we want to drag in networking, sound, rtc etc."
+MACHINE_EXTRA_RRECOMMENDS = "kernel-module-smsc95xx kernel-module-snd-soc-twl4030 kernel-module-rtc-twl \
+  kernel-module-snd-soc-omap kernel-module-snd-soc-omap-mcbsp kernel-module-snd-soc-omap3beagle"

conf/machine/beaglebone.conf

@@ -0,0 +1,19 @@
+#@TYPE: Machine
+#@NAME: BeagleBone machine
+#@DESCRIPTION: Machine configuration for the http://beagleboard.org/bone board
+
+require conf/machine/include/ti33x.inc
+
+KERNEL_DEVICETREE = "am335x-bone.dtb am335x-boneblue.dtb \
+                    am335x-boneblack.dtb am335x-boneblack-wireless.dtb \
+                    am335x-bonegreen.dtb am335x-bonegreen-wireless.dtb"
+
+# Only has DVI connector for external screen
+MACHINE_GUI_CLASS = "bigscreen"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+
+IMAGE_INSTALL_append = " kernel-devicetree kernel-image-zimage"
+
+# Refine the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_BOARDS = "bbbAM335x"

conf/machine/c665x-evm.conf

@@ -0,0 +1,9 @@
+#@TYPE: Machine
+#@NAME: Keystone 1 c665x machine
+#@DESCRIPTION: Machine configuration for the TI Keystone 1 c665x EVM
+
+require conf/machine/include/c66x.inc
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "c6657"
+TI_PDK_LIMIT_BOARDS = "evmC6657"

conf/machine/c667x-evm.conf

@@ -0,0 +1,9 @@
+#@TYPE: Machine
+#@NAME: Keystone 1 c667x machine
+#@DESCRIPTION: Machine configuration for the TI Keystone 1 c667x EVM
+
+require conf/machine/include/c66x.inc
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "c6678"
+TI_PDK_LIMIT_BOARDS = "evmC6678"

conf/machine/dra7xx-evm.conf

@@ -8,19 +8,20 @@ MACHINE_FEATURES += "touchscreen"
 
 SERIAL_CONSOLES = "115200;ttyS0"
 
-KERNEL_DEVICETREE_PREFIX = " \
-    dra7 \
-    ti/dra7 \
-    ti/lcd \
-    ti/omap/dra7 \
-"
-
 KERNEL_DEVICETREE = " \
-    ti/omap/dra7-evm.dtb \
-    ti/omap/dra71-evm.dtb \
-    ti/omap/dra72-evm.dtb \
-    ti/omap/dra72-evm-revc.dtb \
-    ti/omap/dra76-evm.dtb \
+    dra7-evm.dtb \
+    ti/dra7x-evm-osd-lcd-common.dtbo \
+    dra71-evm.dtb \
+    ${@oe.utils.conditional('ARAGO_BRAND', 'mainline', '', 'dra71-evm-nand.dtb', d)} \
+    ti/dra71-evm-lcd-auo-g101evn01.0.dtbo \
+    dra72-evm.dtb \
+    dra72-evm-revc.dtb \
+    ti/dra72-evm-touchscreen.dtbo \
+    ti/dra74-evm-touchscreen.dtbo \
+    dra76-evm.dtb \
+    ti/dra76-evm-tfp410.dtbo \
+    ti/lcd-osd101t2045.dtbo \
+    ti/lcd-osd101t2587.dtbo \
 "
 
 UBOOT_MACHINE = "dra7xx_evm_config"
@@ -45,3 +46,7 @@ MKUBIFS_ARGS = "-F -m 2048 -e 126976 -c 8192"
 # UBI: sub-page size:              512
 # UBI: VID header offset:          2048 (aligned 2048)
 UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512 -O 2048"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_BOARDS = "evmDRA72x evmDRA75x evmDRA78x"
+TI_PDK_LIMIT_SOCS = "dra72x dra75x dra78x"

conf/machine/dra7xx-hs-evm.conf

@@ -11,19 +11,9 @@ UBOOT_LOADADDRESS = "0x82000000"
 UBOOT_RD_LOADADDRESS = "0x84000000"
 UBOOT_RD_ENTRYPOINT = "0x84000000"
 
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_AUTO}/dra7"
+
 OPTEEMACHINE = "ti-dra7xx"
 OPTEEFLAVOR = "dra7xx"
+OPTEEOUTPUTMACHINE = "ti"
 OPTEEPAGER = "y"
-
-EXTRA_IMAGEDEPENDS += "optee-os"
-
-# FIT image for legacy secure devices
-KERNEL_CLASSES += " kernel-fitimage-legacyhs"
-KERNEL_IMAGETYPES += " fitImage"
-
-# FIT image settings
-FITIMAGE_HASH_ALGO = ""
-FITIMAGE_PACK_TEE = "1"
-FITIMAGE_DTB_BY_NAME = "1"
-FITIMAGE_TEE_BY_NAME = "1"
-FITIMAGE_CONF_BY_NAME = "1"

conf/machine/include/am62axx.inc

@@ -0,0 +1,30 @@
+require conf/machine/include/k3.inc
+SOC_FAMILY_append = ":am62axx"
+
+MACHINE_FEATURES += "screen touchscreen"
+
+SERIAL_CONSOLES = "115200;ttyS0 115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+TFA_K3_SYSTEM_SUSPEND = "1"
+
+# Default tiboot3.bin on AM62A is for HS-FS
+BBMULTICONFIG = "k3r5-hs-fs"
+do_image_wic[mcdepends] = "mc::k3r5-hs-fs:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5-hs-fs:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM62A is for HS-FS, add a version for GP
+BBMULTICONFIG += "k3r5-gp"
+IMAGE_BOOT_FILES += " tiboot3-am62ax-gp-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-gp:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-gp:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM62A is for HS-FS, add a version for HS-SE
+BBMULTICONFIG += "k3r5-hs-se"
+IMAGE_BOOT_FILES += " tiboot3-am62ax-hs-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-hs-se:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-hs-se:ti-sci-fw:do_deploy"
+
+TFA_BOARD = "lite"
+OPTEEMACHINE = "k3-am62x"
+OPTEEOUTPUTMACHINE = "k3"

conf/machine/include/am62xx-lp.inc

@@ -0,0 +1,24 @@
+require conf/machine/include/k3.inc
+SOC_FAMILY_append = ":am62xx"
+
+MACHINE_FEATURES += "screen touchscreen"
+
+SERIAL_CONSOLES = "115200;ttyS0 115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+TFA_K3_SYSTEM_SUSPEND = "1"
+
+# Default tiboot3.bin on AM62x LP is for HS-FS
+BBMULTICONFIG = "k3r5-hs-fs"
+do_image_wic[mcdepends] = "mc::k3r5-hs-fs:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5-hs-fs:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM62x LP is for HS-FS, add a version for HS-SE
+BBMULTICONFIG += "k3r5-hs-se"
+IMAGE_BOOT_FILES += " tiboot3-am62x-hs-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-hs-se:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-hs-se:ti-sci-fw:do_deploy"
+
+TFA_BOARD = "lite"
+OPTEEMACHINE = "k3-am62x"
+OPTEEOUTPUTMACHINE = "k3"

conf/machine/include/am62xx.inc

@@ -0,0 +1,30 @@
+require conf/machine/include/k3.inc
+SOC_FAMILY_append = ":am62xx"
+
+MACHINE_FEATURES += "screen touchscreen"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+TFA_K3_SYSTEM_SUSPEND = "1"
+
+# Default tiboot3.bin on AM62x is for HS-FS
+BBMULTICONFIG = "k3r5-hs-fs"
+do_image_wic[mcdepends] = "mc::k3r5-hs-fs:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5-hs-fs:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM62x is for HS-FS, add a version for GP
+BBMULTICONFIG += "k3r5-gp"
+IMAGE_BOOT_FILES += " tiboot3-am62x-gp-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-gp:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-gp:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM62x is for HS-FS, add a version for HS-SE
+BBMULTICONFIG += "k3r5-hs-se"
+IMAGE_BOOT_FILES += " tiboot3-am62x-hs-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-hs-se:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-hs-se:ti-sci-fw:do_deploy"
+
+TFA_BOARD = "lite"
+OPTEEMACHINE = "k3-am62x"
+OPTEEOUTPUTMACHINE = "k3"

conf/machine/include/am64xx.inc

@@ -0,0 +1,41 @@
+require conf/machine/include/k3.inc
+SOC_FAMILY_append = ":am64xx"
+
+MACHINE_FEATURES += "screen touchscreen"
+
+SERIAL_CONSOLES = "115200;ttyS2 115200;ttyS1"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am642-evm.dtb \
+    ti/k3-am642-sk.dtb \
+    ti/k3-am642-evm-icssg1-dualemac.dtbo \
+    ti/k3-am642-evm-icssg1-dualemac-mii.dtbo \
+    ti/k3-am642-evm-nand.dtbo \
+"
+
+# Default tiboot3.bin on AM64x is for SR2.0 HS-FS
+BBMULTICONFIG = "k3r5-sr2-hs-fs"
+do_image_wic[mcdepends] = "mc::k3r5-sr2-hs-fs:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5-sr2-hs-fs:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM64x is for SR2.0 HS-FS, add a version for GP
+BBMULTICONFIG += "k3r5-gp"
+IMAGE_BOOT_FILES += " tiboot3-am64x-gp-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-gp:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-gp:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on AM64x is for SR2.0 HS-FS, add a version for SR2.0 HS-SE
+BBMULTICONFIG += "k3r5-sr2-hs-se"
+IMAGE_BOOT_FILES += " tiboot3-am64x_sr2-hs-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-sr2-hs-se:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-sr2-hs-se:ti-sci-fw:do_deploy"
+
+TFA_BOARD = "lite"
+OPTEEMACHINE = "k3-am64x"
+OPTEEOUTPUTMACHINE = "k3"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "am64x"
+TI_PDK_LIMIT_BOARDS = "am64x_evm"
+TI_PDK_LIMIT_CORES = "mcu1_0 mpu1_0 mcu1_1 mcu2_0 mcu2_1"

conf/machine/include/am65xx.inc

@@ -0,0 +1,40 @@
+require conf/machine/include/k3.inc
+SOC_FAMILY_append = ":am65xx"
+
+MACHINE_FEATURES += "screen touchscreen gpu"
+
+SERIAL_CONSOLES = "115200;ttyS2 115200;ttyS1"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am654-base-board.dtb \
+    ti/k3-am654-base-board-sr1.dtbo \
+    ti/k3-am654-gp.dtbo \
+    ti/k3-am654-idk.dtbo \
+    ti/k3-am654-idk-sr1.dtbo \
+    ti/k3-am654-sr1.dtbo \
+    ti/k3-am654-pcie-usb2.dtbo \
+    ti/k3-am654-pcie-usb3.dtbo \
+    ti/k3-am654-evm-tc358876.dtbo \
+    ti/k3-am654-evm-oldi-lcd1evm.dtbo \
+    ti/k3-am654-evm-ov5640.dtbo \
+"
+
+BBMULTICONFIG += "k3r5-sr2"
+
+# Since J721e does not support multi-cert tiboot3.bin add standalone sysfw.itb
+IMAGE_BOOT_FILES += "sysfw.itb"
+
+# Since default sysfw.itb on AM65x is for SR2.0, add a version for SR1.0
+IMAGE_BOOT_FILES += "sysfw-am65x-evm.itb"
+
+do_image_wic[mcdepends] += "mc::k3r5-sr2:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-sr2:ti-sci-fw:do_deploy"
+
+OPTEEMACHINE = "k3-am65x"
+OPTEEOUTPUTMACHINE = "k3"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "am65xx"
+TI_PDK_LIMIT_BOARDS = "am65xx_evm am65xx_idk"
+TI_PDK_LIMIT_CORES = "mcu1_0 mpu1_0"

conf/machine/include/c66x.inc

@@ -0,0 +1,9 @@
+require conf/machine/include/keystone.inc
+SOC_FAMILY_append = ":c66x"
+
+# HACK: The c66x family is composed of devices with only DSP cores, and no ARM
+#       cores. The Linux kernel is not supported on these machines.
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-dummy"
+EXTRA_IMAGEDEPENDS = ""
+
+IMAGE_FSTYPES = "tar.xz"

conf/machine/include/davinci.inc

@@ -0,0 +1,22 @@
+require conf/machine/include/tune-arm926ejs.inc
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r54"
+
+KERNEL_IMAGETYPE = "zImage"
+
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+UBOOT_MACHINE = "davinci_dvevm_config"
+
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
+
+EXTRA_IMAGEDEPENDS += "u-boot"
+
+SERIAL_CONSOLES ?= "115200;ttyS0"
+EXTRA_IMAGECMD_jffs2 = "--pad --little-endian --eraseblock=0x20000 -n"
+
+MACHINE_FEATURES = "kernel26 serial ethernet usbhost usbgadget mmc alsa"

conf/machine/include/dra7xx.inc

@@ -1,4 +1,4 @@
 require conf/machine/include/omap-a15.inc
-SOC_FAMILY:append = ":dra7xx"
+SOC_FAMILY_append = ":dra7xx"
 
 MACHINE_FEATURES += "pci"

conf/machine/include/j7.inc

@@ -0,0 +1,10 @@
+require conf/machine/include/k3.inc
+SOC_FAMILY_append = ":j7"
+
+OPTEEMACHINE = "k3-j721e"
+OPTEEOUTPUTMACHINE = "k3"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "j721e j7200"
+TI_PDK_LIMIT_BOARDS = "j721e_evm j7200_evm"
+TI_PDK_LIMIT_CORES = "mpu1_0 mcu1_0 mcu1_1 mcu2_0 mcu2_1 mcu3_0 mcu3_1 c66xdsp_1 c66xdsp_2 c7x_1"

conf/machine/include/k2e.inc

@@ -0,0 +1,6 @@
+require conf/machine/include/keystone.inc
+SOC_FAMILY_append = ":k2e"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "k2e"
+TI_PDK_LIMIT_BOARDS = "evmK2E"

conf/machine/include/k2g.inc

@@ -0,0 +1,6 @@
+require conf/machine/include/keystone.inc
+SOC_FAMILY_append = ":k2g"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "k2g"
+TI_PDK_LIMIT_BOARDS = "evmK2G iceK2G"

conf/machine/include/k2hk.inc

@@ -0,0 +1,6 @@
+require conf/machine/include/keystone.inc
+SOC_FAMILY_append = ":k2hk"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "k2h k2k"
+TI_PDK_LIMIT_BOARDS = "evmK2H evmK2K"

conf/machine/include/k2l.inc

@@ -0,0 +1,6 @@
+require conf/machine/include/keystone.inc
+SOC_FAMILY_append = ":k2l"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "k2l"
+TI_PDK_LIMIT_BOARDS = "evmK2L"

conf/machine/include/k3.inc

@@ -1,19 +1,26 @@
 # TI K3 Aarch64 profile for Cortex-A53/A72 cores
 
 require conf/machine/include/ti-soc.inc
-SOC_FAMILY:append = ":k3"
+SOC_FAMILY_append = ":k3"
 
 require conf/machine/include/arm/arch-arm64.inc
 
-require conf/machine/include/ti-bsp.inc
+BBMULTICONFIG += "k3r5"
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r0"
+
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
 
 KERNEL_IMAGETYPE = "Image"
 KERNEL_IMAGETYPES = "Image fitImage"
 KERNEL_CLASSES += "kernel-fitimage"
 
 UBOOT_ARCH = "arm"
-UBOOT_ENTRYPOINT = "0x81000000"
-UBOOT_LOADADDRESS = "0x81000000"
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
 UBOOT_RD_LOADADDRESS = "0x84000000"
 UBOOT_RD_ENTRYPOINT = "0x84000000"
 UBOOT_DTB_LOADADDRESS = "0x83000000"
@@ -24,36 +31,27 @@ SPL_BINARY = "tispl.bin"
 SPL_BINARYNAME = "tispl.bin"
 UBOOT_SUFFIX = "img"
 
-UBOOT_SIGN_ENABLE = "1"
-UBOOT_MKIMAGE_DTCOPTS = "-I dts -O dtb"
-UBOOT_SIGN_KEYNAME ?= "custMpk"
-UBOOT_SIGN_KEYDIR ?= "${TI_SECURE_DEV_PKG}/keys"
-FIT_HASH_ALG ?= "sha512"
-FIT_SIGN_ALG ?= "rsa4096"
-
 EXTRA_IMAGEDEPENDS += "virtual/bootloader"
 
-MACHINE_ESSENTIAL_EXTRA_RDEPENDS += "kernel-image-image"
-
 TFA_PLATFORM = "k3"
+TFA_BOARD = "generic"
+
+MACHINE_GUI_CLASS = "smallscreen"
 
 # Use the expected value of the ubifs filesystem's volume name in the kernel
 # and u-boot.
 UBI_VOLNAME = "rootfs"
 
 # List common SoC features, may need to add touchscreen for specific machines
-MACHINE_FEATURES = "apm usbgadget usbhost vfat ext2 alsa pci"
+MACHINE_FEATURES = "kernel26 apm usbgadget usbhost vfat ext2 alsa ethernet pci"
 
 IMAGE_FSTYPES += "tar.xz wic.xz wic.bmap"
 
 IMAGE_BOOT_FILES ?= "${SPL_BINARYNAME} u-boot.${UBOOT_SUFFIX} tiboot3.bin"
-IMAGE_EFI_BOOT_FILES ?= "${IMAGE_BOOT_FILES}"
-
-EFI_PROVIDER ?= "grub-efi"
-MACHINE_FEATURES += "efi"
-
-WKS_FILE ?= "${@bb.utils.contains("MACHINE_FEATURES", "efi", "sdimage-2part-efi.wks.in", "sdimage-2part.wks", d)}"
 
+WKS_FILE ?= "sdimage-2part.wks"
 do_image_wic[depends] += "virtual/bootloader:do_deploy"
+do_image_wic[mcdepends] += "mc::k3r5:virtual/bootloader:do_deploy mc::k3r5:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5:virtual/bootloader:do_deploy mc::k3r5:ti-sci-fw:do_deploy"
 
-SERIAL_CONSOLES = "115200;ttyS0 115200;ttyS2"
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_K3}"

conf/machine/include/k3r5.inc

@@ -0,0 +1,26 @@
+# TI K3 Armv7 profile for Cortex-R5F cores
+
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":k3r5"
+
+# The closest of existing tunes for Cortex-R5F
+DEFAULTTUNE = "armv7athf"
+require conf/machine/include/tune-cortexa8.inc
+
+# R5 runs early bootloader and loads SYSFW
+# https://git.ti.com/cgit/ti-u-boot/ti-u-boot/tree/board/ti/am65x/README
+# https://git.ti.com/cgit/ti-u-boot/ti-u-boot/tree/board/ti/j721e/README
+PREFERRED_PROVIDER_virtual/kernel = "linux-dummy"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+SPL_BINARY = ""
+UBOOT_SUFFIX = "bin"
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl.${UBOOT_SUFFIX}"
+
+PACKAGECONFIG_pn-u-boot-ti-staging = ""
+PACKAGECONFIG_pn-u-boot-ti-mainline = ""
+
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_K3}"

conf/machine/include/keystone.inc

@@ -0,0 +1,30 @@
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":keystone"
+
+DEFAULTTUNE ?= "armv7athf-neon"
+require conf/machine/include/tune-cortexa15.inc
+
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r10"
+
+KERNEL_IMAGETYPE = "zImage"
+
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
+
+SPL_BINARY = "MLO"
+UBOOT_SUFFIX = "bin"
+
+# Use the expected value of the ubifs filesystem's volume name in the kernel
+# and u-boot.
+UBI_VOLNAME = "rootfs"
+
+EXTRA_IMAGEDEPENDS += "u-boot"
+EXTRA_IMAGEDEPENDS += "boot-monitor"
+
+MACHINE_FEATURES = "kernel26 apm usbgadget usbhost vfat pci dsp"
+MACHINE_FEATURES_BACKFILL_CONSIDERED = "rtc"

conf/machine/include/omap-a15.inc

@@ -1,15 +1,15 @@
 require conf/machine/include/ti-soc.inc
-SOC_FAMILY:append = ":omap-a15"
+SOC_FAMILY_append = ":omap-a15"
 
 DEFAULTTUNE ?= "armv7athf-neon"
-require conf/machine/include/arm/armv7a/tune-cortexa15.inc
+require conf/machine/include/tune-cortexa15.inc
 
-require conf/machine/include/ti-bsp.inc
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r7"
 
-# Graphics providers and variables
-require conf/machine/include/mesa-pvr.inc
-PREFERRED_PROVIDER_virtual/gpudriver ?= "${BSP_SGX_DRIVER_PROVIDER}"
-PVR_DISPLAY_CONTROLLER_ALIAS ?= "omapdrm"
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
 
 KERNEL_IMAGETYPE = "zImage"
 KERNEL_IMAGETYPES = "zImage uImage"
@@ -19,7 +19,7 @@ UBOOT_ARCH = "arm"
 UBOOT_ENTRYPOINT = "0x80008000"
 UBOOT_LOADADDRESS = "0x80008000"
 
-DEVICETREE_FILE = "${@(d.getVar('KERNEL_DEVICETREE') or "").replace("ti/omap/","").replace("ti/","")}"
+DEVICETREE_FILE = "${@(d.getVar('KERNEL_DEVICETREE') or "").replace("ti/","")}"
 
 # Generate an extlinux.conf file
 UBOOT_EXTLINUX = "1"
@@ -35,18 +35,21 @@ UBOOT_SUFFIX = "img"
 
 EXTRA_IMAGEDEPENDS += "virtual/bootloader"
 
-MACHINE_ESSENTIAL_EXTRA_RDEPENDS += "kernel-image-zimage"
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
+XSERVER = "xserver-xorg \
+           xf86-input-evdev \
+           xf86-video-fbdev"
 
-MACHINE_ESSENTIAL_EXTRA_RRECOMMENDS += "vpdma-fw goodix-fw"
+MACHINE_GUI_CLASS = "smallscreen"
 
 # Use the expected value of the ubifs filesystem's volume name in the kernel
 # and u-boot.
 UBI_VOLNAME = "rootfs"
 
 # List common SoC features, may need to add touchscreen for specific machines
-MACHINE_FEATURES = "apm usbgadget usbhost vfat ext2 screen alsa gpu mmip dsp gc320"
+MACHINE_FEATURES = "kernel26 apm usbgadget usbhost vfat ext2 screen alsa ethernet gpu mmip dsp gc320"
 
 IMAGE_FSTYPES += "tar.xz wic.xz wic.bmap"
 WKS_FILE ?= "sdimage-2part.wks"
 IMAGE_BOOT_FILES ?= "${SPL_BINARY} u-boot.${UBOOT_SUFFIX} ${UBOOT_EXTLINUX_BOOT_FILES}"
-do_image_wic[depends] += "virtual/bootloader:do_deploy"
+do_image_wic[depends] += "u-boot:do_deploy"

conf/machine/include/omap3.inc

@@ -0,0 +1,42 @@
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":omap3"
+
+DEFAULTTUNE ?= "armv7athf-neon"
+require conf/machine/include/tune-cortexa8.inc
+
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
+
+# For built-in LCD, add xf86-input-tslib
+XSERVER = "xserver-xorg \
+           xf86-input-evdev \
+           xf86-input-mouse \
+           xf86-video-fbdev \
+           xf86-input-keyboard"
+
+# Default to external video, change to smallscreen for built-in LCD
+MACHINE_GUI_CLASS = "bigscreen"
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r127"
+
+KERNEL_IMAGETYPE = "zImage"
+
+# Default providers, may need to override for specific machines
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+KERNEL_DEVICETREE = "omap3-beagle.dtb omap3-beagle-xm.dtb omap3-beagle-xm-ab.dtb omap3-evm.dtb omap3-evm-37xx.dtb am3517-evm.dtb"
+
+UBOOT_ARCH = "arm"
+UBOOT_MACHINE = "omap3_evm_config"
+XLOAD_MACHINE = "omap3evm_config"
+
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
+
+# If SPL is not used, may need to add x-load
+EXTRA_IMAGEDEPENDS += "u-boot"
+
+# List common SoC features, may need to add touchscreen/ethernet for specific machines
+MACHINE_FEATURES = "kernel26 apm usbgadget usbhost vfat ext2 screen alsa gpu"

conf/machine/include/omap4.inc

@@ -0,0 +1,26 @@
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":omap4"
+
+DEFAULTTUNE ?= "armv7athf-neon"
+require conf/machine/include/tune-cortexa9.inc
+
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
+XSERVER = "xserver-xorg \
+           xf86-input-evdev \
+           xf86-video-fbdev"
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r4"
+
+KERNEL_IMAGETYPE = "zImage"
+
+UBOOT_MACHINE = "omap4_panda_config"
+
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
+
+EXTRA_IMAGEDEPENDS += "u-boot"

conf/machine/include/omapl1.inc

@@ -0,0 +1,2 @@
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":omapl1"

conf/machine/include/omapl137.inc

@@ -0,0 +1,5 @@
+require conf/machine/include/omapl1.inc
+SOC_FAMILY_append = ":omapl137"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "omapl137"

conf/machine/include/omapl138.inc

@@ -0,0 +1,5 @@
+require conf/machine/include/omapl1.inc
+SOC_FAMILY_append = ":omapl138"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "omapl138"

conf/machine/include/ti-soc.inc

@@ -1,8 +1,5 @@
 # This is a generic TI SOC family. It is a superset of all other SOCs
 # and platforms defined in meta-ti to allow BSP-level overrides.
 SOC_FAMILY = "ti-soc"
-require conf/machine/include/soc-family.inc
-
-# TI platforms all use devicetrees with overlays
-MACHINE_ESSENTIAL_EXTRA_RDEPENDS += "kernel-devicetree"
 KERNEL_DTB_OVERLAY_SUPPORT ?= "1"
+require conf/machine/include/soc-family.inc

conf/machine/include/ti33x.inc

@@ -0,0 +1,74 @@
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":ti33x"
+
+DEFAULTTUNE ?= "armv7athf-neon"
+require conf/machine/include/tune-cortexa8.inc
+
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
+
+# For built-in LCD, add xf86-input-tslib
+XSERVER = "xserver-xorg \
+           xf86-input-evdev \
+           xf86-input-mouse \
+           xf86-video-fbdev \
+           xf86-input-keyboard"
+
+# Default to external video, change to smallscreen for built-in LCD
+MACHINE_GUI_CLASS = "bigscreen"
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r22"
+
+# Default providers, may need to override for specific machines
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+KERNEL_IMAGETYPE = "zImage"
+
+KERNEL_DEVICETREE = " \
+    am335x-evm.dtb am335x-evmsk.dtb \
+    am335x-icev2.dtb \
+    am335x-pocketbeagle.dtb am335x-bone.dtb am335x-boneblue.dtb \
+    am335x-bonegreen.dtb am335x-bonegreen-wireless.dtb \
+    am335x-boneblack.dtb am335x-boneblack-wireless.dtb \
+    am335x-sancloud-bbe.dtb \
+"
+
+KERNEL_DEVICETREE += "${@oe.utils.conditional('ENABLE_TI_UIO_DEVICES', '1', 'am335x-icev2-pru-excl-uio.dtb', '', d)}"
+
+UBOOT_ARCH = "arm"
+UBOOT_MACHINE = "am335x_evm_config"
+
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
+
+# Generate an extlinux.conf file
+UBOOT_EXTLINUX = "1"
+UBOOT_EXTLINUX_ROOT = "root=PARTUUID=${uuid}"
+UBOOT_EXTLINUX_BOOT_FILES = " \
+    extlinux.conf;extlinux/extlinux.conf \
+    ${KERNEL_IMAGETYPE} \
+    ${KERNEL_DEVICETREE} \
+"
+
+SPL_BINARY = "MLO"
+UBOOT_SUFFIX = "img"
+
+# Use the expected value of the ubifs filesystem's volume name in the kernel
+# and u-boot.
+UBI_VOLNAME = "rootfs"
+
+EXTRA_IMAGEDEPENDS += "virtual/bootloader"
+
+# List common SoC features, may need to add touchscreen for specific machines
+MACHINE_FEATURES = "kernel26 apm usbgadget usbhost vfat ext2 screen alsa ethernet gpu"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "am335x"
+TI_PDK_LIMIT_BOARDS = "evmAM335x icev2AM335x iceAMIC110 bbbAM335x skAM335x"
+
+IMAGE_FSTYPES += "tar.xz wic.xz wic.bmap"
+WKS_FILE ?= "sdimage-2part.wks"
+IMAGE_BOOT_FILES ?= "${SPL_BINARY} u-boot.${UBOOT_SUFFIX} ${UBOOT_EXTLINUX_BOOT_FILES}"
+do_image_wic[depends] += "virtual/bootloader:do_deploy"

conf/machine/include/ti43x.inc

@@ -0,0 +1,73 @@
+require conf/machine/include/ti-soc.inc
+SOC_FAMILY_append = ":ti43x"
+
+DEFAULTTUNE ?= "armv7athf-neon"
+require conf/machine/include/tune-cortexa9.inc
+
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
+
+# For built-in LCD, add xf86-input-tslib
+XSERVER = "xserver-xorg \
+           xf86-input-evdev \
+           xf86-input-mouse \
+           xf86-video-fbdev \
+           xf86-input-keyboard"
+
+# Default to external video, change to smallscreen for built-in LCD
+MACHINE_GUI_CLASS = "bigscreen"
+
+# Increase this everytime you change something in the kernel
+MACHINE_KERNEL_PR = "r3"
+
+# Default providers, may need to override for specific machines
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-ti-staging"
+PREFERRED_PROVIDER_virtual/bootloader = "u-boot-ti-staging"
+PREFERRED_PROVIDER_u-boot = "u-boot-ti-staging"
+
+KERNEL_IMAGETYPE = "zImage"
+
+KERNEL_DEVICETREE = " \
+    am437x-gp-evm.dtb \
+    ${@oe.utils.conditional('ARAGO_BRAND', 'mainline', '', 'am437x-gp-evm-hdmi.dtb', d)} \
+    am437x-sk-evm.dtb am437x-idk-evm.dtb \
+    am43x-epos-evm.dtb \
+    ${@oe.utils.conditional('ARAGO_BRAND', 'mainline', '', 'am43x-epos-evm-hdmi.dtb', d)} \
+"
+
+KERNEL_DEVICETREE += "${@oe.utils.conditional('ENABLE_TI_UIO_DEVICES', '1', 'am437x-idk-pru-excl-uio.dtb', '', d)}"
+
+UBOOT_ARCH = "arm"
+UBOOT_MACHINE = "am43xx_evm_config"
+
+UBOOT_ENTRYPOINT = "0x80008000"
+UBOOT_LOADADDRESS = "0x80008000"
+
+# Generate an extlinux.conf file
+UBOOT_EXTLINUX = "1"
+UBOOT_EXTLINUX_ROOT = "root=PARTUUID=${uuid}"
+UBOOT_EXTLINUX_BOOT_FILES = " \
+    extlinux.conf;extlinux/extlinux.conf \
+    ${KERNEL_IMAGETYPE} \
+    ${KERNEL_DEVICETREE} \
+"
+
+SPL_BINARY = "MLO"
+UBOOT_SUFFIX = "img"
+
+# Use the expected value of the ubifs filesystem's volume name in the kernel
+# and u-boot.
+UBI_VOLNAME = "rootfs"
+
+EXTRA_IMAGEDEPENDS += "u-boot"
+
+# List common SoC features, may need to add touchscreen for specific machines
+MACHINE_FEATURES = "kernel26 apm usbgadget usbhost vfat ext2 screen alsa ethernet gpu"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_SOCS = "am437x"
+TI_PDK_LIMIT_BOARDS = "evmAM437x idkAM437x skAM437x"
+
+IMAGE_FSTYPES += "tar.xz wic.xz wic.bmap"
+WKS_FILE ?= "sdimage-2part.wks"
+IMAGE_BOOT_FILES ?= "${SPL_BINARY} u-boot.${UBOOT_SUFFIX} ${UBOOT_EXTLINUX_BOOT_FILES}"
+do_image_wic[depends] += "u-boot:do_deploy"

conf/machine/j7-evm-k3r5.conf

@@ -1,8 +1,6 @@
 #@TYPE: Machine
-#@NAME: BeagleBone AI-64 (R5F)
-#@DESCRIPTION: Machine configuration for the BeagleBone AI-64 (R5F core)
-
-TI_PREFERRED_BSP ?= "bb_org"
+#@NAME: J7 EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J7 EVM (R5F core)
 
 require conf/machine/include/k3r5.inc
 
@@ -17,7 +15,3 @@ UBOOT_IMAGE = "tiboot3-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
 UBOOT_SYMLINK = "tiboot3-${MAINMACHINE}.${UBOOT_SUFFIX}"
 
 UBOOT_MACHINE = "j721e_evm_r5_defconfig"
-UBOOT_MACHINE:bsp-ti-6_6 = "j721e_beagleboneai64_r5_defconfig"
-
-UBOOT_CONFIG_FRAGMENTS:bsp-bb_org = "j721e_beagleboneai64_r5.config"
-UBOOT_CONFIG_FRAGMENTS:bsp-ti-6_1 = "j721e_beagleboneai64_r5.config"

conf/machine/j7-evm.conf

@@ -0,0 +1,45 @@
+#@TYPE: Machine
+#@NAME: J7 EVM
+#@DESCRIPTION: Machine configuration for the TI J7 EVM
+
+require conf/machine/include/j7.inc
+
+MACHINE_FEATURES += "gpu"
+
+SERIAL_CONSOLES = "115200;ttyS2 115200;ttyS3"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+# Since J721e does not support multi-cert tiboot3.bin add standalone sysfw.itb
+IMAGE_BOOT_FILES += "sysfw.itb"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-j721e-common-proc-board.dtb \
+    ti/k3-j721e-proc-board-tps65917.dtb \
+    ti/k3-j721e-common-proc-board-infotainment.dtbo \
+    ti/k3-j721e-cpb-csi2-ov5640.dtbo \
+    ti/k3-j721e-fpdlink-cpb-fusion.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-3.dtbo \
+    ti/k3-j721e-sk.dtb \
+    ti/k3-j721e-fpdlink-sk-fusion.dtbo \
+    ti/k3-j721e-sk-csi2-ov5640.dtbo \
+    ti/k3-j721e-sk-rpi-cam-imx219.dtbo \
+    ti/k3-j721e-common-proc-board-uarts.dtbo \
+    ti/k3-j7200-mcspi-loopback.dtbo \
+"
+
+UBOOT_MACHINE = "j721e_evm_a72_config"

conf/machine/j7-hs-evm-k3r5-sr1-1.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: J7 SR1.1 HS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J7 SR1.1 HS EVM (R5F core)
+
+# Booting SR1.1 requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/j7-hs-evm-k3r5.conf
+SOC_FAMILY_append = ":k3r5-sr1-1"
+
+SYSFW_SOC = "j721e_sr1_1"
+SYSFW_SYMLINK = "sysfw.itb"

conf/machine/j7-hs-evm-k3r5.conf

@@ -0,0 +1,18 @@
+#@TYPE: Machine
+#@NAME: J7 HS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J7 HS EVM (R5F core)
+
+require conf/machine/include/k3r5.inc
+
+SYSFW_SOC = "j721e"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs"
+SYSFW_SYMLINK = ""
+
+SPL_BINARY = "spl/u-boot-spl.${UBOOT_SUFFIX}"
+SPL_SYMLINK = "u-boot-r5spl.${UBOOT_SUFFIX}"
+UBOOT_BINARY = "tiboot3.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "tiboot3-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "tiboot3-${MAINMACHINE}.${UBOOT_SUFFIX}"
+
+UBOOT_MACHINE = "j721e_hs_evm_r5_defconfig"

conf/machine/j7-hs-evm.conf

@@ -0,0 +1,19 @@
+#@TYPE: Machine
+#@NAME: J7 HS EVM
+#@DESCRIPTION: Machine configuration for the TI J7 HS EVM
+
+require conf/machine/j7-evm.conf
+
+UBOOT_MACHINE = "j721e_hs_evm_a72_defconfig"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"
+SYSFW_SYMLINK = ""
+
+BBMULTICONFIG += "k3r5-sr1-1"
+
+# Since default sysfw.itb on J7 is for SR1.1, add a version for SR1.0
+IMAGE_BOOT_FILES += "sysfw-j721e-evm.itb"
+do_image_wic[mcdepends] += "mc::k3r5-sr1-1:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-sr1-1:ti-sci-fw:do_deploy"

conf/machine/j7200-evm.conf

@@ -0,0 +1,19 @@
+#@TYPE: Machine
+#@NAME: J7200 EVM
+#@DESCRIPTION: Machine configuration for the TI J7200 EVM
+
+require conf/machine/include/j7.inc
+
+SERIAL_CONSOLES = "115200;ttyS2 115200;ttyS3"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-j7200-common-proc-board.dtb \
+    ti/k3-j7200-mcspi-loopback.dtbo \
+    ti/k3-j7200-common-proc-board-uarts.dtbo \
+"
+
+UBOOT_MACHINE = "j7200_evm_a72_config"
+
+do_image_wic[mcdepends] = "mc::k3r5:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5:ti-sci-fw:do_deploy"

conf/machine/j7200-hs-evm-k3r5.conf

@@ -8,4 +8,4 @@ SYSFW_SOC = "j7200_sr2"
 SYSFW_CONFIG = "evm"
 SYSFW_SUFFIX = "hs"
 
-UBOOT_MACHINE = "j7200_evm_r5_defconfig"
+UBOOT_MACHINE = "j7200_hs_evm_r5_defconfig"

conf/machine/j7200-hs-evm.conf

@@ -4,4 +4,8 @@
 
 require conf/machine/j7200-evm.conf
 
-UBOOT_MACHINE = "j7200_evm_a72_defconfig"
+UBOOT_MACHINE = "j7200_hs_evm_a72_defconfig"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"

conf/machine/j721s2-evm-k3r5-gp.conf

@@ -0,0 +1,20 @@
+#@TYPE: Machine
+#@NAME: J721S2 GP EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J721S2 GP EVM (R5F core)
+
+# Booting GP requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-gp"
+
+SYSFW_SOC = "j721s2"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "gp"
+SYSFW_TIBOOT3_SYMLINK = "tiboot3.bin"
+
+UBOOT_MACHINE = "j721s2_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-gp-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-gp.${UBOOT_SUFFIX}"

conf/machine/j721s2-evm-k3r5-sr1-hs-fs.conf

@@ -0,0 +1,15 @@
+#@TYPE: Machine
+#@NAME: J721S2 HS-FS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J721S2 HS-FS EVM (R5F core)
+
+# Booting HS-FS requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-sr1-hs-fs"
+
+SYSFW_SOC = "j721s2"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs-fs"
+SYSFW_TIBOOT3_SYMLINK = ""
+
+UBOOT_MACHINE = "j721s2_evm_r5_defconfig"

conf/machine/j721s2-evm.conf

@@ -0,0 +1,57 @@
+#@TYPE: Machine
+#@NAME: J721S2 EVM
+#@DESCRIPTION: Machine configuration for the TI J721S2 EVM
+
+require conf/machine/include/j7.inc
+
+MACHINE_FEATURES += "gpu"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+TFA_K3_USART = "0x8"
+OPTEEMACHINE = "k3-j784s4"
+OPTEE_K3_USART = "0x8"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am68-sk-base-board.dtb \
+    ti/k3-am68-sk-bb-csi2-ov5640.dtbo \
+    ti/k3-am68-sk-bb-rpi-cam-imx219.dtbo \
+    ti/k3-am68-sk-fpdlink-fusion.dtbo \
+    ti/k3-am68-sk-rpi-hdr-ehrpwm.dtbo \
+    ti/k3-am68-sk-som-ddr_mem_carveout.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-3.dtbo \
+    ti/k3-j721s2-common-proc-board.dtb \
+    ti/k3-j721s2-cpb-csi2-ov5640.dtbo \
+    ti/k3-j721s2-fpdlink-cpb-fusion.dtbo \
+    ti/k3-j721s2-gesi-exp-board.dtbo \
+    ti/k3-j721s2-common-proc-board-uarts.dtbo \
+    ti/k3-j7200-mcspi-loopback.dtbo \
+"
+
+UBOOT_MACHINE = "j721s2_evm_a72_defconfig"
+
+# Default tiboot3.bin on J721S2 is for GP
+BBMULTICONFIG = "k3r5-gp"
+do_image_wic[mcdepends] = "mc::k3r5-gp:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5-gp:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on J721S2 is for GP, add a version for SR1.0 HS-FS
+BBMULTICONFIG += "k3r5-sr1-hs-fs"
+IMAGE_BOOT_FILES += " tiboot3-j721s2-hs-fs-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-sr1-hs-fs:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-sr1-hs-fs:ti-sci-fw:do_deploy"

conf/machine/j721s2-hs-evm-k3r5.conf

@@ -8,4 +8,4 @@ SYSFW_SOC = "j721s2"
 SYSFW_CONFIG = "evm"
 SYSFW_SUFFIX = "hs"
 
-UBOOT_MACHINE = "j721s2_evm_r5_defconfig"
+UBOOT_MACHINE = "j721s2_hs_evm_r5_defconfig"

conf/machine/j721s2-hs-evm.conf

@@ -0,0 +1,27 @@
+#@TYPE: Machine
+#@NAME: J721S2 HS EVM
+#@DESCRIPTION: Machine configuration for the TI J721S2 HS EVM
+
+require conf/machine/include/j7.inc
+
+MACHINE_FEATURES += "gpu"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+TFA_K3_USART = "0x8"
+OPTEEMACHINE = "k3-j784s4"
+OPTEE_K3_USART = "0x8"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-j721s2-common-proc-board.dtb \
+    ti/k3-j721s2-gesi-exp-board.dtbo \
+"
+
+UBOOT_MACHINE = "j721s2_hs_evm_a72_defconfig"
+
+do_image_wic[mcdepends] = "mc::k3r5:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5:ti-sci-fw:do_deploy"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"

conf/machine/j784s4-evm-k3r5-gp.conf

@@ -0,0 +1,20 @@
+#@TYPE: Machine
+#@NAME: J784S4 GP EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J784S4 GP EVM (R5F core)
+
+# Booting GP requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-gp"
+
+SYSFW_SOC = "j784s4"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "gp"
+SYSFW_TIBOOT3_SYMLINK = "tiboot3.bin"
+
+UBOOT_MACHINE = "j784s4_evm_r5_defconfig"
+
+SPL_BINARY = ""
+UBOOT_BINARY = "u-boot-spl.${UBOOT_SUFFIX}"
+UBOOT_IMAGE = "u-boot-r5spl-gp-${MAINMACHINE}-${PV}-${PR}.${UBOOT_SUFFIX}"
+UBOOT_SYMLINK = "u-boot-r5spl-gp.${UBOOT_SUFFIX}"

conf/machine/j784s4-evm-k3r5-sr1-hs-fs.conf

@@ -0,0 +1,16 @@
+#@TYPE: Machine
+#@NAME: J784S4 HS-FS EVM (R5F)
+#@DESCRIPTION: Machine configuration for the TI J784S4 HS-FS EVM (R5F core)
+
+# Booting HS-FS requires different SYSFW, the rest is handled at runtime
+
+require conf/machine/include/k3r5.inc
+SOC_FAMILY_append = ":k3r5-sr1-hs-fs"
+
+SYSFW_SOC = "j784s4"
+SYSFW_CONFIG = "evm"
+SYSFW_SUFFIX = "hs-fs"
+SYSFW_TIBOOT3_SYMLINK = ""
+SYSFW_SYMLINK = ""
+
+UBOOT_MACHINE = "j784s4_evm_r5_defconfig"

conf/machine/j784s4-evm.conf

@@ -0,0 +1,58 @@
+#@TYPE: Machine
+#@NAME: J784S4 EVM
+#@DESCRIPTION: Machine configuration for the TI J784S4 EVM
+
+require conf/machine/include/j7.inc
+
+MACHINE_FEATURES += "gpu"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+TFA_K3_USART = "0x8"
+OPTEEMACHINE = "k3-j784s4"
+OPTEE_K3_USART = "0x8"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-am69-sk.dtb \
+    ti/k3-am69-sk-csi2-ov5640.dtbo \
+    ti/k3-am69-sk-ddr-mem-carveout.dtbo \
+    ti/k3-am69-sk-fpdlink-fusion.dtbo \
+    ti/k3-am69-sk-rpi-hdr-ehrpwm.dtbo \
+    ti/k3-am69-sk-rpi-cam-imx219.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-cm-1-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-0-3.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-0.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-1.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-2.dtbo \
+    ti/k3-j721e-fpdlink-imx390-rcm-1-3.dtbo \
+    ti/k3-j784s4-evm.dtb \
+    ti/k3-j784s4-evm-csi2-ov5640.dtbo \
+    ti/k3-j784s4-fpdlink-fusion.dtbo \
+    ti/k3-j784s4-evm-uarts.dtbo \
+    ti/k3-j7200-mcspi-loopback.dtbo \
+"
+
+UBOOT_MACHINE = "j784s4_evm_a72_defconfig"
+
+# Default tiboot3.bin on J784S4 is for GP
+BBMULTICONFIG = "k3r5-gp"
+do_image_wic[mcdepends] = "mc::k3r5-gp:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5-gp:ti-sci-fw:do_deploy"
+
+# Since default tiboot3.bin on J784S4 is for GP, add a version for SR1.0 HS-FS
+BBMULTICONFIG += "k3r5-sr1-hs-fs"
+IMAGE_BOOT_FILES += " tiboot3-j784s4-hs-fs-evm.bin"
+do_image_wic[mcdepends] += "mc::k3r5-sr1-hs-fs:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] += "mc::k3r5-sr1-hs-fs:ti-sci-fw:do_deploy"
+
+TFA_BOARD = "j784s4"

conf/machine/j784s4-hs-evm.conf

@@ -0,0 +1,28 @@
+#@TYPE: Machine
+#@NAME: J784S4 HS EVM
+#@DESCRIPTION: Machine configuration for the TI J784S4 HS EVM
+
+require conf/machine/include/j7.inc
+
+MACHINE_FEATURES += "gpu"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+SERIAL_CONSOLES_CHECK = "${SERIAL_CONSOLES}"
+TFA_K3_USART = "0x8"
+OPTEEMACHINE = "k3-j784s4"
+OPTEE_K3_USART = "0x8"
+
+KERNEL_DEVICETREE = " \
+    ti/k3-j784s4-evm.dtb \
+"
+
+UBOOT_MACHINE = "j784s4_evm_a72_defconfig"
+
+do_image_wic[mcdepends] = "mc::k3r5:ti-sci-fw:do_deploy"
+do_image_tar[mcdepends] = "mc::k3r5:ti-sci-fw:do_deploy"
+
+TFA_BOARD = "j784s4"
+
+SPL_BINARY = "tispl.bin_HS"
+UBOOT_BINARY = "u-boot.img_HS"
+UBOOT_SYMLINK = "u-boot.img"

conf/machine/k2e-evm.conf

@@ -0,0 +1,32 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2E machine
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2E EVM
+
+require conf/machine/include/k2e.inc
+
+KERNEL_DEVICETREE = "keystone-k2e-evm.dtb"
+
+UBOOT_MACHINE = "k2e_evm_config"
+
+BOOT_MONITOR_MAKE_TARGET = "k2e"
+
+IMAGE_FSTYPES += "ubifs ubi tar.xz"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+
+SYSVINIT_ENABLED_GETTYS = ""
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    126976 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 3856 LEBs
+MKUBIFS_ARGS = "-F -m 2048 -e 126976 -c 3856"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              2048
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 2048 -O 2048"

conf/machine/k2e-hs-evm.conf

@@ -0,0 +1,15 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2E HS EVM
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2E HS EVM
+
+require conf/machine/k2e-evm.conf
+
+UBOOT_MACHINE = "k2e_hs_evm_config"
+SPL_BINARY = ""
+
+UBOOT_ENTRYPOINT = "0x82000000"
+UBOOT_LOADADDRESS = "0x82000000"
+UBOOT_RD_LOADADDRESS = "0x84000000"
+UBOOT_RD_ENTRYPOINT = "0x84000000"
+
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_CAT}/k2e"

conf/machine/k2g-evm.conf

@@ -0,0 +1,35 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2G machine
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2G EVM
+
+require conf/machine/include/k2g.inc
+
+MACHINE_FEATURES += "alsa"
+
+KERNEL_DEVICETREE = "keystone-k2g-evm.dtb keystone-k2g-ice.dtb \
+                     ${@oe.utils.conditional('ENABLE_TI_UIO_DEVICES', '1', 'keystone-k2g-ice-pru-excl-uio.dtb', '', d)}"
+
+UBOOT_MACHINE = "k2g_evm_config"
+
+BOOT_MONITOR_MAKE_TARGET = "k2g"
+
+IMAGE_FSTYPES += "ubifs ubi tar.xz"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+
+SYSVINIT_ENABLED_GETTYS = ""
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    4096
+# UBI: logical eraseblock size:    253952 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1926 LEBs
+MKUBIFS_ARGS = "-F -m 4096 -e 253952 -c 1926"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    4096
+# UBI: physical eraseblock size:   256 KiB
+# UBI: sub-page size:              4096
+UBINIZE_ARGS = "-m 4096 -p 256KiB -s 4096 -O 4096"

conf/machine/k2g-hs-evm.conf

@@ -0,0 +1,15 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2G HS EVM
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2G HS EVM
+
+require conf/machine/k2g-evm.conf
+
+UBOOT_MACHINE = "k2g_hs_evm_config"
+SPL_BINARY = ""
+
+UBOOT_ENTRYPOINT = "0x82000000"
+UBOOT_LOADADDRESS = "0x82000000"
+UBOOT_RD_LOADADDRESS = "0x84000000"
+UBOOT_RD_ENTRYPOINT = "0x84000000"
+
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_CAT}/k2g"

conf/machine/k2hk-evm.conf

@@ -0,0 +1,32 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2HK machine
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2HK EVM
+
+require conf/machine/include/k2hk.inc
+
+KERNEL_DEVICETREE = "keystone-k2hk-evm.dtb"
+
+UBOOT_MACHINE = "k2hk_evm_config"
+
+BOOT_MONITOR_MAKE_TARGET = "k2hk"
+
+IMAGE_FSTYPES += "ubifs ubi tar.xz"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+
+SYSVINIT_ENABLED_GETTYS = ""
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    126976 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 3856 LEBs
+MKUBIFS_ARGS = "-F -m 2048 -e 126976 -c 3856"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              2048
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 2048 -O 2048"

conf/machine/k2hk-hs-evm.conf

@@ -0,0 +1,15 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2HK HS EVM
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2HK HS EVM
+
+require conf/machine/k2hk-evm.conf
+
+UBOOT_MACHINE = "k2hk_hs_evm_config"
+SPL_BINARY = ""
+
+UBOOT_ENTRYPOINT = "0x82000000"
+UBOOT_LOADADDRESS = "0x82000000"
+UBOOT_RD_LOADADDRESS = "0x84000000"
+UBOOT_RD_ENTRYPOINT = "0x84000000"
+
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_CAT}/k2hk"

conf/machine/k2l-evm.conf

@@ -0,0 +1,32 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2L machine
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2L EVM
+
+require conf/machine/include/k2l.inc
+
+KERNEL_DEVICETREE = "keystone-k2l-evm.dtb"
+
+UBOOT_MACHINE = "k2l_evm_config"
+
+BOOT_MONITOR_MAKE_TARGET = "k2l"
+
+IMAGE_FSTYPES += "ubifs ubi tar.xz"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+
+SYSVINIT_ENABLED_GETTYS = ""
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    4096
+# UBI: logical eraseblock size:    253952 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1926 LEBs
+MKUBIFS_ARGS = "-F -m 4096 -e 253952 -c 1926"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    4096
+# UBI: physical eraseblock size:   256 KiB
+# UBI: sub-page size:              4096
+UBINIZE_ARGS = "-m 4096 -p 256KiB -s 4096 -O 4096"

conf/machine/k2l-hs-evm.conf

@@ -0,0 +1,15 @@
+#@TYPE: Machine
+#@NAME: Keystone 2 K2L HS EVM
+#@DESCRIPTION: Machine configuration for the TI Keystone 2 K2L HS EVM
+
+require conf/machine/k2l-evm.conf
+
+UBOOT_MACHINE = "k2l_hs_evm_config"
+SPL_BINARY = ""
+
+UBOOT_ENTRYPOINT = "0x82000000"
+UBOOT_LOADADDRESS = "0x82000000"
+UBOOT_RD_LOADADDRESS = "0x84000000"
+UBOOT_RD_ENTRYPOINT = "0x84000000"
+
+TI_SECURE_DEV_PKG = "${TI_SECURE_DEV_PKG_CAT}/k2l"

conf/machine/lego-ev3.conf

@@ -0,0 +1,22 @@
+#@TYPE: Machine
+#@NAME: LEGO Mindstorms EV3
+#@DESCRIPTION: Machine configuration for the LEGO Mindstorms EV3
+
+require conf/machine/include/davinci.inc
+require conf/machine/include/omapl138.inc
+
+UBOOT_MACHINE = "legoev3_config"
+UBOOT_SUFFIX = "bin"
+UBOOT_ENTRYPOINT = "0xC0008000"
+UBOOT_LOADADDRESS = "0xC0008000"
+SPL_BINARY = ""
+
+KERNEL_DEVICETREE = "da850-lego-ev3.dtb"
+KERNEL_IMAGETYPES = "uImage"
+KERNEL_DEVICETREE_BUNDLE = "1"
+SERIAL_CONSOLES = "115200;ttyS1"
+
+IMAGE_FSTYPES += " wic"
+WKS_FILE ?= "sdimage-bootpart.wks"
+WIC_CREATE_EXTRA_ARGS += " --no-fstab-update"
+IMAGE_BOOT_FILES = "${KERNEL_IMAGETYPES}"

conf/machine/omap3evm.conf

@@ -0,0 +1,32 @@
+#@TYPE: Machine
+#@NAME: OMAP3 EVM
+#@DESCRIPTION: Machine configuration for the TI OMAP3 EVM
+
+require conf/machine/include/omap3.inc
+
+MACHINE_GUI_CLASS = "smallscreen"
+MACHINE_FEATURES += "touchscreen ethernet"
+
+IMAGE_FSTYPES += "jffs2 tar.xz"
+EXTRA_IMAGECMD_jffs2 = "-lnp -e 0x20000 -s 2048"
+
+SERIAL_CONSOLES = "115200;ttyS0"
+USE_VT = "0"
+
+EXTRA_IMAGEDEPENDS += "x-load"
+
+# NOTE: there are NAND and OneNAND versions of this board...
+# do ubiattach /dev/ubi_ctrl -m 4
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    129024 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1996 LEBs
+MKUBIFS_ARGS = "-m 2048 -e 129024 -c 1996"
+
+# do ubiattach /dev/ubi_ctrl -m 4
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              512
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512"

conf/machine/omap5-evm.conf

@@ -0,0 +1,34 @@
+#@TYPE: Machine
+#@NAME: OMAP5 EVM
+#@DESCRIPTION: Machine configuration for the TI OMAP5 uEVM
+
+require conf/machine/include/omap-a15.inc
+
+IMAGE_FSTYPES += "ubi tar.xz"
+
+KERNEL_DEVICETREE = "omap5-uevm.dtb"
+
+SERIAL_CONSOLES = "115200;ttyS2"
+
+# UBI information.  Note that this is board and kernel specific.  Changes
+# in your kernel port may require changes in these variables.  For more
+# details about this board please see
+# http://processors.wiki.ti.com/index.php/UBIFS_Support
+
+# do ubiattach /dev/ubi_ctrl -m 7 -O 2048
+# From dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: logical eraseblock size:    126976 bytes
+# from ubiattach stdout:
+# UBI device number 0, total 1988 LEBs
+MKUBIFS_ARGS = "-F -m 2048 -e 126976 -c 4300"
+
+# do ubiattach /dev/ubi_ctrl -m 7 -O 2048
+# from dmesg:
+# UBI: smallest flash I/O unit:    2048
+# UBI: physical eraseblock size:   131072 bytes (128 KiB)
+# UBI: sub-page size:              512
+# UBI: VID header offset:          2048 (aligned 2048)
+UBINIZE_ARGS = "-m 2048 -p 128KiB -s 512 -O 2048"
+
+UBOOT_MACHINE = "omap5_uevm_config"

conf/machine/omapl137-evm.conf

@@ -0,0 +1,15 @@
+#@TYPE: Machine
+#@NAME: OMAP-L137 EVM
+#@DESCRIPTION: Machine configuration for the TI OMAP-L137 EVM board
+
+require conf/machine/include/davinci.inc
+require conf/machine/include/omapl137.inc
+
+# HACK: The omapl137 family does not have linux kernel support.
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-dummy"
+EXTRA_IMAGEDEPENDS = ""
+
+IMAGE_FSTYPES = "tar.xz"
+
+# Set the list of device targets for ti-pdk class recipes
+TI_PDK_LIMIT_BOARDS = "evmOMAPL137"